Kiwi Technics KIWI-106 Скачать руководство пользователя страница 54

Страница: 54 / 60

Table 1.0 Command ID

Data Byte

Data Type

Byte details
7 ------- 0

Data Details

$58 (87)=Load Sequence

0000xxxx

Seq number to load (0-8) - 0 is do not load Seq

$57 (88)=Load Pattern

0000xxxx

Pattern number to load (0-8) - 0 is do not load Pattern

$59 (89)=Voice Mode

00000xxx

xxx =

0=Poly1 (7th note robs oldest)

1=Poly2 (7th note ignored)
2=Unison Legato

3=Unison Staccato
4=Mono Legato

5=Mono Staccato

$5a (90)=Voice Detune Amount Hi 000xxxxx

$5b (91)=Voice Detune Amount Lo 0yyyyyyy

Hi & Lo are combined to make single 12 bit command.
00 0yyyyyyy = 0000xxxx xyyyyyyy

$5c (92)=Detune Control

0000000x

x =

0=unison only,1=All modes except Mono

$5d (93)=Arp Control

00yyy0zz

zz =

00=1Oct,01=2Oct,10=3Oct

yyy =

000=Up,001=Dn,010=U/D,011=Rndm, 100=As Played

$5e (94)=AT Control

00000xyz

z =

DCO LFO (1=on)

y =

VCF Cutoff (1=on)

x =

VCA Level (1=on)

$5f (95)=MW Control

00000xyz

z =

DCO LFO (1=on)

y =

VCF Cutoff (1=on)

x =

VCA Level (1=on)

$60 (96)=Midi Control

0000wxyz

z =

Arp Enable (1=Enabled)

y =

Sequence Enable (1=Enabled)

x =

Pattern Enable (1=Enabled)

w =

Hold Enabled (1=Hold On)

$61 (97)=Patch Clock Tempo

0000xxxx

0000yyyy

If this is nonzero it will replace the internal Clock

speed with this value. If this value is zero the
internal clock will remain unchanged.

This byte is sent as two nibbles which are combined to
make single 8 bit command.

00 0000yyyy = xxxxyyyy

www.kiwitechnics.com

Kiwi-106 Upgrade User Manual v204

Содержание KIWI-106





























































Результаты поиска

Содержание KIWI-106

Отзывы:

Похожие инструкции для KIWI-106

Бренды по названию

Популярные бренды

Kiwi Technics KIWI-106, Руководство пользователя

Результаты поиска

Содержание KIWI-106

Отзывы:

Похожие инструкции для KIWI-106

Бренды по названию

Популярные бренды