Kiwi Technics KIWI-106 Скачать руководство пользователя страница 49

Страница: 49 / 60

Table 1.0 Command ID

Data Byte

Data Type

Byte details
7 ------- 0

Data Details

$0c (12) = Not Used

00000000

$0d (13) = Not Used

00000000

$0e (14) = Pattern Level Hi

000xxxxx

$0f (15) = Pattern Level Lo

0yyyyyyy

Hi & Lo are combined to make single 12 bit command.

00 0yyyyyyy = 0000xxxx xyyyyyyy

$10 (16) = Pattern Control

00000xyz

y =

VCA Amount Destination - 0=Off 1=On

z =

VCF Cutoff Destination - 0=Off 1=On

x =

Clock Source – 0=Arp 1=Seq

$11 (17) = Int Clock Rate Hi

0000xxxx

$12 (18) = Int Clock Rate Lo

0000yyyy

This byte is sent as two nibbles which are combined to
make single 8 bit command.

00 0000yyyy = xxxxyyyy
Range is 0-255 for 5-300 BPM

$13 (19) = MW Level

0xxxxxxx

x = Range $00-$7f (0-127)

$14 (20) = AT Level

0xxxxxxx

x = Range $00-$7f (0-127)

$15 (21) = Key Trans Disable

0000000x

x = Disable Key Transpose (0=enable,1=disable)

$16 (22) = Display Mode

000000yz

z =

Clock Display - 0=Off 1=On

y =

Scrolling Display - 0=Off 1=On

$17 (23) = Memory Protect

0000000z

z =

Memory Protect - 0=Protected 1=Not Protected

Note – This is read only and can only be changed by the

Memory Protect Switch on the rear of the Juno-106

$18 (24) = Not Used

00000000

$19 (25) = Internal Tune

0xxxxxxx

x =

Fine Tune Override
0 = use Fine tune on rear of 106

1-127 = Override fine tune

Note – When the fine tune is being overridden changing

the rear tune knob will override this setting

$1a (26) = External Pedal
Polarity

0000000x

x =

Ext Pedal Polarity
0 = Normal Polarity (N/O)

1 = Reverse Polarity (N/C)

$1b-$1f (27-31) = Nulls

Not currently Used

$03 (3) Request Patch Edit Buffer

Dump

No Data

www.kiwitechnics.com

Kiwi-106 Upgrade User Manual v204

Содержание KIWI-106





























































Результаты поиска

Содержание KIWI-106

Отзывы:

Похожие инструкции для KIWI-106

Бренды по названию

Популярные бренды

Kiwi Technics KIWI-106, Руководство пользователя

Результаты поиска

Содержание KIWI-106

Отзывы:

Похожие инструкции для KIWI-106

Бренды по названию

Популярные бренды