Kiwi Technics KIWI-106 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 60

background image

14

Kiwi 106 Menu System

Page 5 –
Global/Patch
Parameter Edit

The digit display will show 'P5', 'gL',
Global Parameter number (1-15) &
Value.

Global Parameters are as follows:

Bank 1 (1) - Midi In Channel
Bank 2 (2) – Midi Out Channel
Bank 3 (3) – Seq Midi Out Ch
Bank 4 (4) – Master Clock Source
Bank 5 (5) – External Pedal Polarity
Bank 6 (6) – Midi Soft Thru
Bank 7 (7) – Midi Prog Change Enable
Bank 8 (8) – Midi CC Enable
Patch 1 (9) – Midi Sysex Enable
Patch 2 (10) – Midi Clock Gen Enable
Patch 3 (11) – Arp Clock Divide*
Patch 4 (12) – Seq Clock Divide*
Patch 5 (13) – Pattern Clock Source
Patch 6 (14) – Pattern Destination

Patch 7 (15) – Dynamics Enable*

Patch 8 – Factory Patch Restore

*=Patch Parameter

Global Parameter Editing is done using
the VCA Level Slider

Note - Dynamics is a Patch parameter
and not a global parameter. This was
moved from global to patch in ver 2.0.
No other buttons were available for
editing this.

Midi In Channel

Bank 1

The Midi In Channel is set using the
VCA Level Control

Range is '01'-'16' or 'On' (Omni)

Midi Out Channel

Bank 2

The Midi Out Channel is set using the
VCA Level Control

Range is '01'-'16'

Midi Seq Out
Channel

Bank 3

The Seq Midi Out Channel is set using
the VCA Level Control

Range is '01'-'16' or 'Of' (Off)

Master Clock Source

Bank 4

This sets the Master Clock Source
from the internal, external or midi
clocks

‘01’ = Internal
‘02' = Midi
‘03' = Ext Step
‘04’ = Ext 24 PPQN
‘05' = Ext 48 PPQN

External Pedal
Polarity

Bank 5

This sets the polarity of the External
Pedal.

'OF'= Normal
'On' = Inverted

Midi Soft Through

Bank 6

The Midi Soft Through sets the way
the 106 handles Midi data.

'01'=

Stop All Midi

'02' = Pass All Midi
'03' = Pass only Non-CC
'04' = Pass only CC that the 106

hasn't used

Midi Prog Change

Bank 7

The Midi Program change command
can be optionally disabled.

'01'=

Disabled

'02' = Midi PC Input Enabled
'03' = Midi PC Output Enabled
'04' = Midi PC Input & Output Enabled

www.kiwitechnics.com

Kiwi-106 Upgrade User Manual v204

«
...
12
13
14
15
16
...
»

Содержание KIWI-106





























































Отзывы:

Нет отзывов

Похожие инструкции для KIWI-106

Бренд: Yamaha Страницы: 56

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 11

Бренд: Yamaha Страницы: 6

Бренд: Korg Страницы: 36

Бренд: CreamWare Страницы: 7

Бренд: CreamWare Страницы: 12

Бренд: CreamWare Страницы: 36

Бренд: Sequential Страницы: 88

Бренд: Yamaha Страницы: 40

Бренд: Hammond Страницы: 16

Бренд: Yamaha Страницы: 148

Бренд: Kawai Страницы: 115

Clavinova CLP-870

Бренд: Yamaha Страницы: 132

Бренд: Bleeplabs Страницы: 2

Essence FM MKII

Бренд: Kodamo Страницы: 31

Бренд: Kodamo Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды