background image

 

 
 
 

 

3

 

Transport and installation 

3.1

 

Storage and transport 

The kiln should be positioned in a dry room with humidity of 
less than 80% to avoid that insulation bricks are absorbing 
moisture.  Protect  the  kiln  against  strong  temperature 
fluctuations and aggressive atmospheres. 
The kiln should be moved in an upright position with a fork-
lift truck or suitable lifting equipment. Lifting equipment must 
not be fixed onto the body, only onto the frame of the kiln. 
During transport the kiln itself can overturn or parts may fall 
down. For this reason, it must be ensured that there are no 
persons in vicinity of the kiln. 
 

3.2

 

Installation 

The kiln should only be installed and operated in a suitable 
room. 

The most important requirements are

 

The size of room must be adequate, dry (relative humidity 
< 80%) and ventilated. 

 

The  floor  should  be  of  stone,  concrete  or  a  material  of 
similar strength and heat resistance. 

 

The  floor  should  be  smooth  and  even  offering  secure 
standing for the kiln. The authorized area loading must not 
be exceeded. 

 

Floors of wood, carpet, plastic or other flammable materials 
which deform and/or inflame with temperatures < 75°C are 
not acceptable. 

 

The  installation  must  allow  free  heat  radiation  during 
operation without the risk of ignition of objects, floor, walls 
or  ceiling.  The  following  minimum  distance  is 
recommended: 

o

 

from the wall: 0,2 m 

o

 

from the ceiling: 0,5 m 

 

Ceilings and walls must not be of flammable materials like 
wood,  carpet  or  other  materials  which  deform  with 
temperatures  lower  than  250°C.  Otherwise  a  lateral 
distance of minimum 1m must be observed, respectively a 
fire-proof  insulation  should  be  mounted  on  the  ceiling 

Содержание CB Series

























Отзывы: