If igniters stop sparking,
the battery should be
replaced.
1. Lift up at bottom of
battery tray and slide
battery tray out.
2. Remove battery and
replace with alkaline
9-volt battery.
3. Slide battery tray back
into compartment.
7
IMPORTANT:
Light only one burner at a
time.
Do not lean over burners. Push in and
turn to “LITE” the control knob for the
burner you wish to use.
You will hear the “snapping” sound of
the spark. Once burner is lit, turn knob
from the “LITE” position to the desired
setting. Repeat for the other burner as
needed.
IMPORTANT:
If burner does not light
immediately, turn the burner knob to
“OFF” and wait 5 minutes before
relighting.
Manually lighting the burners
1. Strike a match to light it.
2. Carefully guide the lit match to the
burner you wish to light.
3. Push in and turn the burner knob to
“LITE” for the burner closest to the lit
match. The burner will light
immediately.
4. Repeat steps 1 through 3 for each
burner.
IMPORTANT:
If burner does not light
immediately, turn the burner knob to
“OFF” and wait 5 minutes before
relighting.
If any burners do not light after
attempting to manually light them,
contact the KitchenAid Assistance Center
(see “Requesting Assistance or Service”
section).
Lighting the side burner
front
burner
rear
burner
Replacing the Igniter battery
lift up and
slide out tray
Cleaning
General Tips
IMPORTANT:
Before cleaning, make sure
all controls are off and the burners are
cool. Always follow label instructions on
cleaning products.
For routine cleaning, wash with soap and
water using a soft cloth or sponge. Rinse
with clean water and dry at once with a
soft, lint-free cloth to avoid spots and
streaks.
Never use steel wool to clean the side
burner, as it will scratch the surface.
Stainless Steel
IMPORTANT:
Do not use soap-filled
scouring pads, abrasive cleaners,
Cooktop Polishing Creme, steel wool,
gritty wash cloths or paper towels.
Cleaners should not contain chlorine.
Damage may occur to the product finish.
Rub in direction of grain to avoid
scratching or damaging the surface.
Food spills should be cleaned as soon as
entire Side Burner is cool. Spills may
cause permanent discoloration.
• Use Stainless Steel Cleaner & Polish
(Part #4396095). See “Requesting
Assistance or Service” section to order.
• Use a mild liquid detergent or all-
purpose cleaner according to label
instructions.
• Rinse with clean water and dry at once
with soft, lint-free cloth to avoid spots
and streaks.
• Use vinegar to remove hard water
spots. Rinse with water and dry
thoroughly.
• Use a glass cleaner to remove
fingerprints.
IMPORTANT:
Make sure gas supply is off
and all control knobs are in the “OFF”
position. Make sure the Side Burner is
cool.
Exterior
The quality of this material resists most
stains and pitting, providing that the
surface is kept clean and protected.
• Apply stainless steel polish to all non-
cooking areas before first use. Re-apply
after each cleaning to prevent
permanent damage to surface.
• Cleaning should always be followed by
rinsing with clean warm water.
• Wipe the surface completely dry with a
soft cloth.
• For tough spots or baked-on grease,
use Whirlpool Degreaser (Part No.
31552), a commercial degreaser
designed for stainless steel. See
“Requesting Assistance or Service”
section to order.
Interior
• Cleaning should always be followed by
rinsing with clean, warm water.
• Use a mild liquid detergent or all-
purpose cleaner, following label
instructions. Rinse with clean water and
dry completely with a soft, lint-free
cloth.
• A heavy-duty scrub sponge can be used
with mild cleaning products. Always rub
in the direction of the grain.
• For small, difficult-to-clean areas, use
Whirlpool Degreaser (Part No. 31552), a
commercial degreaser designed for
stainless steel. See “Requesting
Assistance or Service” section to order.
Burner caps and grate
• Clean with a brass bristle brush.
• Wash grate using mild detergent, warm
water and degreaser.
• Rinse with clean water and dry with
soft, lint-free cloth.
• Use Stainless Steel Cleaner & Polish
(Part No. 4396095). See “Requesting
Assistance or Service” section to order.
Knobs, plastic and flange area
around knobs
IMPORTANT:
Do not use steel wool,
abrasive cleaners, or oven cleaner.
Do not soak knobs.
• Wash with mild detergent, using a soft
cloth and warm water. Rinse and dry.
Control panel graphics
IMPORTANT
: Do not use steel wool,
abrasive cleaners or oven cleaner.
Do not spray cleaner directly onto panel.
Clean around the burner labels gently;
scrubbing may remove printing.
• Wash with mild detergent, using a soft
cloth and warm water. Rinse and dry.
