KitchenAid KDTE104ESS3, Техническая спецификация

Страница: 3 / 12

3
Service Diagnostics Cycle
Service Diagnostics Cycle Notes:
Customer Cycle Operation
To quickly advance through customer cycles, invoke the Rapid Advance
mode by pressing HIGH TEMP - HEATED DRY - HIGH TEMP - HEATED DRY,
after starting the cycle. Then, press START/RESUME to advance through
cycle intervals.
NOTE: Rapid Advance mode is automatically enabled in the Service
Diagnostics cycle but must be manually invoked in customer cycles.
26 25 24 23 22 21 18 17 16 15 14 13 12 11 10 9 8
7
6 5 4 3 2
1
INTERVAL
CYCLE, OPTION, AND STATUS LEDs
NORMAL
HI TEMP
DRY OPTION
1 HR WASH
START/RESUME
RUNNING (Front Status light)
SANITIZED
CLEAN/ 7-Seg
ALL OTHER CYCLE, OPTION, AND STATUS LEDs
NRM
NRM NRM NRM
NRM
NRM NRM NRM
NRM
NRM NRM
NRM
HIT HIT HIT HIT HIT HIT HIT HIT
HIT HIT
HIT HIT
DRY DRY DRY DRY DRY DRY DRY DRY
DRY
DRY
DRY
1HR
1HR
1HR
1HR 1HR 1HR
1HR
1HR 1HR 1HR 1HR 1HR
STA STA STA STA STA STA STA
STA STA
STA STA STA STA STA STA STA STA STA STA STA STA
STA STA
RUN RUN RUN RUN RUN RUN RUN RUN RUN RUN RUN RUN RUN RUN RUN RUN RUN RUN RUN RUN RUN RUN RUN RUN
SAN (SAN)
(SAN)
CLN
7-Seg
(CLN) (CLN)
ALL
NOTE 5
4,5,6 NOTES
INTERVAL TIME (min:sec)
TOTAL TIME (MAX.): 22:57
SOIL SENSING INTERVALS
AND SENSOR CHECKS
NOTE 5
OWI (SOIL SENSOR) CHECK INTERVALS NOTE 6
NOTE: OWI has thermistor built in - see check above
THERMISTOR (TEMPERATURE SENSOR)
CHECK INTERVAL
NOTE 8
SALT LEVEL REED SWITCH/
FLOWMETER INPUT TEST
LOADS
PILOT RELAY
VENT
FILL
WASH MOTOR
DISPENSER (DETERGENT/RINSE AID)
DRAIN MOTOR
DC FAN MOTOR (IF PRESENT)
HEATER
REGEN (IF PRESENT)
0:06 0:08 0:08 0:08 0:08 0:10 0:05
0:23
0:05 1:00
2:00
0:30 1:00 0:30 4:00
0:01 0:01
0:01 0:01
1:52
0:06
2:30 0:08
0:08
OWI OWI
THR
PLT PLT
PLT PLT PLT PLT PLT PLT PLT PLT PLT PLT PLT PLT PLT PLT
VNT VNT VNT VNT VNT VNT VNT VNT VNT VNT VNT VNT VNT VNT VNT VNT
FIL FIL FIL
WSH WSH WSH WSH
WSH WSH WSH
DSP
DRN DRN DRN
FAN
HTR HTR
REG
2
CUST
OMER ERR
OR 1
CUST
OMER ERR
OR 2
CUST
OMER ERR
OR 3
CUST
OMER ERR
OR 4
SER
VICE ERR
OR 1
SER
VICE ERR
OR 2
S
T
A
N
D
B
Y
1 1
8
19
NRM
DRY
STA
RUN
(CLN)
0:44
4
5
HIT HIT
PLT
VNT
DRN
S
T
A
N
D
B
Y
1 1 1 1
6 6 6
1HR
STA
SRM
NOTE 7
DIVERTER POSITION SENSOR CHECK NOTE 3
DIVERTER
DIVERTER POSITION
DIV
(DIV) (DIV)
(DIV) (DIV) DIV
UPR UPR UPR UPR UPR UPR UPR ON LOW LOW LOW LOW LOW LOW LOW TZ
FAN FAN FAN
3
3 3 3 3
7
20
1HR
STA
RUN
(CLN)
9
0:01
HIT
7-Seg 7-Seg 7-Seg
7-Seg 7-Seg
AC FAN MOTOR (IF PRESENT)
1
To invoke the Diagnostics cycle, perform the following while
in standby:
■
Press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no
more than 1 second between key presses.
■
The Service Diagnostics Cycle will start when the door is closed.
■
To rapid advance 1 interval at a time, press the Start/Resume key.
Rapid advance may skip sensor checks as some checks require
2 complete intervals.
NOTE: While you are in the Diagnostic Cycle, the Start/Resume
feature is turned Off (for example, Auto Resume after door interrupts)
and the Start/Resume key becomes an interval advance key.
■
Invoking Service Diagnostics Cycle clears all status and last run
information from memory and restores defaults. It also forces the
next cycle to
be a Sensor Calibration cycle.
■
Drain and wash motors will pulsate on and off.
■
Last run cycles and options returned to default.
■
Last run delay returns to the lowest delay increment.
■
Calibration cycle may force an extra rinse to occur prior to Final
Rinse (to assure clear water), then calibrates the O.W.I. and the fill
amount during the final rinse.
■
Operating state returns to Standby upon completing or
terminating the Service Diagnostics Cycle.
■
Reference the “Service Diagnostics with Error Codes” section
for details.
2
Turn on all LEDs immediately upon receiving the entry sequence (even
if the door is open) for 5 seconds as a display test. Turn off all LEDs for
1 second prior to reporting customer error history.
3
Diverter will be on continuously in interval 14. In all other diverter
intervals, diverter will be on only until it reaches the intended position
for that interval.
4
Press HI TEMP key in this interval to clear customer error history.
5
Thermistor (temperature sensor) checks - turn clean LED on if
thermistor is in its normal temperature range 32°F to 167°F (0°C to
75°C). Turn sanitized LED on if fill temperature is above 65°F (18.3°C).
6
OWI (optical soil sensor) checks:
■
Check OWI sensor for the presence of water during the 5-sec.
pause in interval 16 and turn on the Clean LED in interval 15 if
water detected.
■
Check OWI sensor for presence of bulk soil during pause interval
13 and turn on the Clean LED in interval 12 if bulk soil detected.
7
DC fan motor is On during upper rack washing intervals.
8
Turn on Sanitized LED in this interval to indicate that the salt level reed
switch is closed.
9
Turn on Clean LED in this interval to indicate that vent current
is detected.