If cooktop does
not operate:
Check that the circuit breaker is not
tripped or the house fuse blown.
Check that the power supply cord is
plugged into the outlet.
Check that gas valves are turned to
the “ON” position.
See Use and Care Guide for
troubleshooting list.
✓
✓
✓
✓
Installer checkoff
list:
Cooktop correctly positioned in
countertop cutout.
Maintained specified distances to
cabinet surfaces.
Cooktop level – front to back – side
to side.
Burner caps positioned properly on
sealed burner bases.
All packing material removed.
Backguard or island trim attached
(see page 4).
✓
✓
✓
✓
✓
✓
If you need
assistance:
The KitchenAid Consumer Assistance Center
will answer any questions about operating or
maintaining your cooktop not covered in the
Installation Instructions. The KitchenAid
Consumer Assistance Center is open 24
hours a day, 7 days a week. Just dial 1-800-
422-1230 — the call is free within the
continental United States, or visit our web site
at www.kitchenaid,com.
When you call, you will need the cooktop
model number and serial number. Both
numbers can be found on the model/serial
rating plate located on the bottom of the
cooktop and are visible through the cutout in
the left-hand back corner of the enclosure
bottom.
If you need
service:
In the event that your KitchenAid
appliance should need service, call the
dealer from whom you purchased the
appliance or a KitchenAid-designated
service company. A KitchenAid-
designated service company is listed in
the Yellow Pages of your telephone
directory under “Appliances —
Household — Major — Service and
Repair.”
You can also obtain the service
company's name and number by dialing,
free within the continental United States,
the KitchenAid Consumer Assistance
Center telephone number, 1-800-422-
1230. A special operator will tell you the
name of your nearest KitchenAid-
designated service company.
Maintain the quality built into your
KitchenAid appliance — call a
KitchenAid-designated service company.
Maintenance
If removing the cooktop is necessary for
maintenance, shut off gas supply.
Disconnect the gas and electric supply.
After disconnecting the gas and electric
supply, finish removing the cooktop.
Generally, the cooktop does not need to
be removed for servicing.
8
16.
Push in and turn each control
knob to the “LO” (or simmer) setting. The
“LO” setting of each burner has been
factory set to the lowest setting possible
to provide a stable flame. If it does not
stay lit on the “LO” setting, check “LO”
setting as follows:
a. Turn control to “LITE” until burner
ignites.
b. Quickly turn knob down to LOWEST
POSITION.
c. If burner goes out, readjust valve as
follows:
Remove the burner control knob. Insert a
flat-blade screwdriver into the hollow
valve stem and engage the slotted screw.
Flame size can be increased or
decreased by turning the screw. Adjust
flame until you can quickly turn knob from
the “HI” to “LO” position without
extinguishing the flame. Flame should be
as small as possible without going out.
Electronic Ignition System —
initial lighting
Cooktop burners use electronic igniters in
place of standing pilots. When the
cooktop control knob is pushed in and
turned to the “LITE” position, the system
creates a spark to light the burner. This
sparking continues until the control knob
is turned to the desired setting.
15.
Check operation of the cooktop
burners. Push in and turn each control
knob to “LITE” position. The flame should
light within 4 seconds. Do Not leave the
knob in the “LITE” position after
burner lights.
If burners do not light properly, turn
control knob to the “OFF” position. Check
that burner cap is in the proper position.
Check that power supply cord is plugged
in and that circuit breaker or house fuse
has not blown. Check that the shutoff
valve is in the “ON” position. Check
operation again. If a burner does not light
at this point, contact your KitchenAid
dealer for assistance.
OFF
LIT
E
COOKTOP
Polarized and grounded 120-volt,
60-Hz, AC, 15-amp fused electrical
supply for power supply cord
connection.
✓
ELECTRICAL
Connection: 1/2" NPT with a
minimum 5/8" (15.9 mm) diameter
flex line.
The cooktop is connected only to
type of gas for which it is certified for
use.
✓
✓
GAS SUPPLY
