background image

5

Gas and Electric

Dimensions

Typical Gas and Electric

Connections

Gas and Electric

Connection Locations

product rating/serial tag

1/2" nipple
(not supplied)

control support panel

shut off valve
(not supplied)

regulated gas
supply line

AGA or CSA approved
flexible stainless
steel gas supply line
(not supplied)

36" (91.4 cm) 
3-prong ground-type 
power supply cord

Front of
Cooktop

regulator (supplied
with product) must be
installed with arrow up
pointing at cooktop
bottom

14" 

(35.6 cm)

10" (25.4 cm)

3-prong ground-type outlet
should be located on left hand
side of cutout 8" (20.3 cm)
max. from enclosure sidewall.

Gas supply line should be
located in this area on rear or
side walls, or the supply line can
come up through the floor.

Note: Solid side and
bottom of cutout
enclosure not shown.

Gas supply

requirements

WARNING

Observe all governing codes and
ordinances.
Important: Cooktop must be connected
to a regulated gas supply.

A.

This installation must conform with

local codes and ordinances. In the
absence of local codes, installations must
conform with American National
Standard, National Fuel Gas Code 
ANSI Z223.1 — latest edition or 
CANI — B149.1 or 2*.

Explosion Hazard

Use a new AGA or CSA approved
gas supply line.

Install a shut-off valve.

Securely tighten all gas
connections.

If connected to LP, have a
qualified person make sure gas
pressure does not exceed 14"
water column.

Examples of a qualified person
include licensed heating
personnel, authorized gas
company personnel, and
authorized service personnel.

Failure to do so can result in
death, explosion, or fire.

B.

Input ratings shown on the

model/serial rating plate are for elevations
up to 2,000 feet (610 m). For elevations
above 2,000 feet (610 m), ratings are
reduced at a rate of 4% for each 1,000
feet (305 m) above sea level.

C.

The cooktop is equipped for use

with NATURAL gas. It is design-certified
by International Approval Services (I.A.S.)
for NATURAL and L.P. gases with
appropriate conversion. The model/serial
rating plate, located on the underside of
the burner box, has information on the
type of gas that can be used. If this
information does not agree with the type
of gas available, check with the local gas
supplier.

Copies of the standards listed may be 
obtained from:

* CSA International

8501 East Pleasant Valley Rd.
Cleveland, Ohio 44131-5575

Содержание 8284670



















Отзывы: