manualshive.com logo in svg

KISANKRAFT KK-CSP-5920, Руководство по эксплуатации, Страница: 36 / 80

Поделиться
Скачать
KISANKRAFT KK-CSP-5920 Скачать руководство пользователя страница 36

 

Chainsaw-Petrol 

KK-CSP-5920/6020/6522/7524

 

 

: www.kisankraft.com 

: [email protected] 

: +91.80. 22178200 

 

Page 36 of 80 

Felling 

WARNING!

 Unless you have special training we advise you not to fell trees 

with a diameter larger than the bar length of your saw! 

 

Directional cuts 

To make the directional cut you begin with the top cut. Aim using to the saw’s felling direction mark 

(1) toward a goal further forward in the terrain, where you would like the tree to fall (2). Stand on 

the right-hand side of the tree, behind the saw, and cut with a pull stroke. 

Next make the bottom cut so that it ends exactly at the end of the top coat. 

The directional cuts should run 1/4 of the diameter through the trunk and the angle between the 

top cut and bottom cut should be 45°. 

The line where the two cuts meet is called the directional cut line. This line should be perfectly 

horizontal and at right angles (90°) to the chosen felling direction

 

 

 

 

 

Felling cut

 

The felling cut is made from the opposite side of the tree and it must be 

perfectly horizontal. Stand on the left side of the tree and cut on the pull 

stroke. Make the felling cut about 3-5 cm (1.5-2 inches) above the bottom 

directional cut. Set the spike bumper (if one is fitted) just behind the felling 

hinge. Use full throttle and advance the chain/bar slowly into the tree. Make 

sure the tree does not start to move in the opposite direction to your 

intended felling direction. 

 

Finish the felling cut parallel with the directional cut line so that the distance 

between them is at least 1/10 of the trunk diameter. 

The uncut section of the trunk is called the felling hinge. The felling hinge 

controls the direction that the tree falls. 

All control over the felling direction is lost if the felling hinge is too narrow 

or non-existent, or if the directional cuts and felling cut are badly placed. 

When the felling cut and directional cut are complete the tree should start 

to fall by itself or with the aid of a felling wedge or breaking bar. 

We recommend that you use a bar that is longer than the diameter of the 

tree, 

There are methods for felling trees with a diameter larger than the bar 

length. However, these methods involve a much greater risk that the 

kickback zone of the bar will come into contact with the tree. 

 

Содержание KK-CSP-5920

















































































Отзывы:

Нет отзывов