Kinze 3600, Руководство оператора

Страница: 61 / 382

6-33 Rev. 7/04
MACHINE OPERATION
KPM II
(MTR28e)
REPLACING A FAULTY SENSOR
To replace a faulty sensor; (a) disconnect the faulty
sensor and check the monitor to be sure the correct
sensor was disconnected, (b) turn the monitor off, (c)
after a few seconds, turn the monitor back on and (d)
plug in the replacement sensor. The monitor will chirp
twice to acknowledge the new sensor was learned and
saved.
To replace more than one faulty sensor, proceed as
stated above beginning with the lowest numbered row
in the rear/left section and continue to replace sensors
in ascending order. Then move on to the front/right
section and continue in ascending order.
If the monitor detects a faulty distance sensor, the lower
LCD will immediately move to the speed display, show
the word “PICKUP” or “RADAR” depending on the
distance sensor installed, and the alarm will sound.
NOTE: If the monitor is not turned off and then on,
the replacement sensor(s) will be ignored until the
next power on, at which point the sensors will be
randomly learned by the monitor.
FIELD OPERATION
Press the ON/OFF key to turn the monitor
on and off.
Information regarding each section is dis-
played alternately every 5 seconds.
REAR/FRONT CONFIGURATION
• Press the SELECT key once to show
REAR section only. (Monitor sets cor-
rect row spacing.)
• Press the SELECT key a second time to
return to each section being displayed
alternately every 5 seconds. (Monitor sets
correct row spacing.)
• Press the SELECT key a third time to
show REAR section only again.
LEFT/RIGHT CONFIGURATION (If Applicable)
• Press the SELECT key once to show
LEFT section only.
• Press the SELECT key a second time to
show RIGHT section only.
• Press the SELECT key a third time to
return to each section being displayed
alternately every 5 seconds.
NOTE: SELECT key has no function when only a
single section is being used.
At power up, the lower LCD will show speed (MPH or
KM/H).
(MTR28c)
(MTR28c)
4. Section Not Selected Warning - If the monitor
was programmed for two sections and only one is
currently selected for display (by pressing the
SELECT key), the icon of the disabled section will
flash for a period of 1 minute, then turn off at each
power up. If seed flow is sensed in the disabled
section, the icon for that section (front, left or right)
will begin to flash.
5. Seed Planting Stopped Warning - When the
monitor detects no seed flow on all rows, the
monitor will emit 3 short beeps to alert the user. This
warning will occur each time the planter is stopped,
each time the planter is raised at the end of a row
or if the mechanical drive fails while planting.
NOTE: This warning will not trigger unless a
minimum time of continuous planting has passed.
6. Seed Counting Sensor In Calibration Warning -
All seed counting sensors run a self-calibration
sequence on power up. While in calibration the
bottom segment of each corresponding bar graph will
flash if the monitor detects movement or planting
activity. If the monitor does not detect this, the message
“WAIT CALIBRATION” will be scrolled.
7. Seed Counting Sensor Too Dirty Warning - After
the seed counting sensors end their internal self-
calibration, the monitor may detect one or more
sensors are either too dirty or blocked. If the monitor
detects planting or movement, the corresponding bar
graph remains flashing. The monitor will display
“CLEAN SENSORS” on the top LCD if no movement
or planting is detected, prompting the user to clean
the tubes. If the tubes are dirty, they will still show
seed flow with less accuracy. If the tubes are blocked
the user will get an alarm as soon as planting starts.
The corresponding bar graph will remain flashing until
the problem is corrected and the monitor is powered
down and then powered back up.
8. Low Battery Warning - The monitor is constantly
monitoring its input voltage to quickly detect low
power conditions. If the monitor detects that the
input voltage has dropped below 11.0V, it will
display “LO SYS” on the lower LCD, provided that
the monitor does not detect speed or planting.
NOTE: After the alarms have been acknowledged
and if the alarm condition is still present, the LCD
will continue to display the alarm condition.