Kintech Engineering Geovane Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 49

Kintech Engineering Geovane Скачать руководство пользователя страница 16

17

3.4

Commissioning

It may happen that the Geovane is not able to update its True North offset output
before the installation team leaves the site (e.g. if the installation takes place on
a foggy day).

To verify that the Geovane has been correctly connected, the following values
must be checked:

Output

Variable

Read value

Diagnosis

Analog
voltage

True North
offset

-45º

not working*

0…360º (370º by default)

OK

Tilt X / Tilt Y

-112.5º

not working*

-90º…90º

OK

Frequency

True North
offset

-30º

not working*

0…360º (370º by default)

OK

Digital

Any

Answers polls

OK

*Troubleshooting:



Check that the Geovane is powered on.



Check wiring (refer to section 3.2).



Check that the output has been enabled (see configuration in section 8).

Remarks:

Before the Geovane gets GPS signal, the True North offset outputs are set to
380º (GPS fix is typically obtained 30 seconds after power on, provided open-
sky conditions).

Prior to installing the Geovane, we strongly recommend that a bench system
test be carried out to confirm the system is configured correctly, is fully
functional and electrically compatible with the selected host system and
cabling (preferably utilizing the final cable length).

«
...
14
15
16
17
18
...
»

Содержание Geovane


















































Отзывы:

Нет отзывов