manualshive.com logo in svg

Kintech Engineering Geovane, Руководство пользователя, Страница: 15 / 49

Поделиться
Скачать
Kintech Engineering Geovane Скачать руководство пользователя страница 15

16 

Remark:  

It is recommended to always keep the RS-485 cores (pins 2 and 4) accessible 
from  the  ground  so  the  Geovane  can  be  re-configured  and  updated  without 
having to dismount it from the met mast. 

 

3.3.1

 

Cable shielding 

It is critical that appropriate shielding is used to reduce EMI. The connection of 
the cable shield depends on whether or not the mounting of the Geovane on the 
boom is isolated. 

If the mounting of the Geovane is isolated (i.e. non-metallic adaptor sleeve), the 
cable  shield  between  the  Geovane  and  the  data  acquisition  system  must  be 
applied at both sides. 

When the mounting of the Geovane is non-isolated (i.e. metallic adaptor sleeve), 
the cable shield between the Geovane and the data acquisition system must be 
applied one-sided at the data acquisition device. 

Both cases assume that the metallic measurement mast and the data acquisition 
system are grounded. 

 

 

Содержание Geovane


















































Отзывы:

Нет отзывов