Kingsman ZDV3318 Series Скачать руководство пользователя

Страница: 54 / 59

Approved for Power Vent PVH58 / PVH58FM

- This appliance is approved for use with a Kingsman PVH58 Horizontal Power Vent -

A Horizontal Power Vent Termination is intended for use where standard venting configurations are

not possible.

NOTE:

MODELS EQUIPPPED WITH MILLIVOLT/ STANDING PILOT IGNITION: Downward vertical vent runs are

NOT

permitted.

NOTE:

MODELS EQUIPPPED WITH INTERMITTENT PILOT IGNITION (Proflame 1 or Proflame 2):

Downward vertical vent runs are permitted, however, Cold Climate Switch (Standing Pilot Mode) must

NOT

be used.

Seven 90° elbows are possible if the total horizontal is not more than 25ft and the vertical does not exceed 15ft.

Refer to Power Vent Manual for proper installation and use.

Maximum / Minimum Vent Lengths:

Maximum

Vent Length is 125 ft plus six 90° elbows with Air Intake Shutter fully closed. Termination must not be

below unit.
This power vent can be installed up to

8ft

below the installed fireplace on runs less than 100ft and not more than

four 90° elbows.

Minimum

Vent Length is 1 FT vertical x 3 FT horizontal x 3 FT vertical x 3 FT horizontal (See PVH58 manual).

Содержание ZDV3318 Series




























































Результаты поиска

Содержание ZDV3318 Series

Отзывы:

Похожие инструкции для ZDV3318 Series

Бренды по названию

Популярные бренды

Kingsman ZDV3318 Series, Руководство по установке

Результаты поиска

Содержание ZDV3318 Series

Отзывы:

Похожие инструкции для ZDV3318 Series

Бренды по названию

Популярные бренды