Kingsman ZDV3318 Series Скачать руководство пользователя страница 29

Страница: 29 / 59

Gas Conversion –Part A ZDV3318

1. Remove [3]screws from false bottom.

Remove the false bottom and air

restrictor.

2. Remove [2]screws the from main burner.

Slide main burner to the left, and lift out

of fireplace.

3. Adjust the Air Shutter to the correct

Primary Air setting as specified in the

manual or on the label plate. To adjust

the Primary Air setting, loosen screw on

the side of the Air Shutter and rotate to

the correct opening using a drill bit or

tape measure. Retighten screw.

4. Remove the Main Orifice using a ½”

wrench and replace with the new

Conversion Orifice which came with the

Conversion Kit.

5. Replace the main burner. Install the new

Pilot Orifice (See

Pilot Conversion

) and

Hi/Lo valve regulator by following

instructions supplied with the Conversion

Kit.

Replace air restrictor and false bottom

WARNING: This conversion kit shall be installed by a qualified service agency in accordance with the

manufacturer’s instruction s and all applicable codes and requirements of the authority having jurisdiction. If the

information in these instructions is not followed exactly a fire, explosion or production of carbon monoxide may result

causing property damage, personal injury or loss of life. The qualified service agency is responsible for the proper

installation of this kit. The installation is not proper and complete until the operation of the converted appliance is checked

as specified in the manufacturer’s instructions supplied with kit.

Caution:

The gas supply shall be shut off prior to disconnecting the electrical power, before proceeding with the conversion

Содержание ZDV3318 Series




























































Результаты поиска

Содержание ZDV3318 Series

Отзывы:

Бренды по названию

Популярные бренды

Kingsman ZDV3318 Series, Руководство по установке

Результаты поиска

Содержание ZDV3318 Series

Отзывы:

Бренды по названию

Популярные бренды