Kingsman ZDV3318 Series Скачать руководство пользователя

Страница: 18 / 59

Fan Kit Installation

Fan installation Instructions for ZDV6000 / 3320 /3318
/3318MQ / 3622 / 3622RB with or without CVCK (Clean View
Circulating Kit).

Note:

Install Fan Kit Before Installing optional CVCK

(Clean

View Circulating Kit).

If CVCK has been installed into framing additional access is

provided by removing screws from bottom panel of CVCK.

See

Installing Clean View Kit (CVCK).

1. Slide fan housing into unit and place over 2 Fan Retainer Tabs. Tabs

are pre punched and bent up (

*Note: on 6000/3320 units, these

Tabs are located on the right side of the unit

). Rubber grommets

at the base of the fan should fit snugly over the tabs.

2. For Fan Disc Installation these units have been installed with a sliding

track system. Install the Thermodisc provided with the Fan Kit. Place

Thermodisc into sliding assembly (

Fig.1

), and attach 2 leads exiting

right side of the fan housing into thermodisc. Now slide disc assembly

into thermodisc track (

Fig.2

). Place swivel handle of disc assembly

on track to lock into position. To service disc simply pull swivel handle

slide towards you while rotating handle to access disc.

Caution: Label all wires prior to disconnection when

servicing controls. Wiring errors can cause improper and

dangerous operation.

Verify proper operation after servicing.

Parts List:

1ea. Fan comes with 4ft cord. Two 14” leads (female ends)

1ea. Variable speed control (wall mount type)

1ea. Thermodisc

1 Thermodisc mount assembly

3. Wire Junction Box and wall mounted variable speed control to

120v. Install a duplex outlet to junction box and plug fan into

outlet.

4. Turn the wall switch on (clockwise). Turn fireplace on. Once the

sensor in the unit reaches operating temperature (approximately

10 to 15 minutes) the fan will turn on. The fan can be switched

off if desired by turning the wall switch fully counter clockwise.

5. To set the minimum fan speed, remove the variable switch from

the wall mount. Turn the variable speed wall controller to its

minimum setting (fully counterclockwise). Use the set screw on

the side of the variable speed controller to increase or decrease

the minimum fan speed (lowering the minimum fan speed will

decrease sound level created by fan).

Reinstall switch into wall mount and cover with face plate.

Note:

To service fan with CVCK Kit installed see Removing

Burner System in manual. If CVCK is finished with a MQSW

Wall Surround the MQSW may be removed by removing the

4 attachment screws and removing the MQSW

allowing access into the bottom of the fireplace to service

blower.

Electrical Services

All optional Fan Kits are equipped with a 120V, 60Hz, .4amp blower.

Note: All electric connections are to be made in accordance with

CSA Standard C22.1 – Canadian Electrical Code part I or with the

National Electrical Code, ANSI/NFPA 70 (latest edition) and /or in

accordance with local codes.

Warning: Electrical Grounding Instructions. This

appliance is equipped with a three-pronged (grounding)

plug for your protection against shock hazard and

should be plugged directly into a properly grounded

three-prong receptacle. Do not cut or remove the

grounding prong from this plug.

CAUTION: DO NOT ATTACH 120V FAN ASSEMBLY TO MILLIVOLT GAS VALVE SYSTEM

Содержание ZDV3318 Series




























































Результаты поиска

Содержание ZDV3318 Series

Отзывы:

Похожие инструкции для ZDV3318 Series

Бренды по названию

Популярные бренды

Kingsman ZDV3318 Series, Руководство по установке

Результаты поиска

Содержание ZDV3318 Series

Отзывы:

Похожие инструкции для ZDV3318 Series

Бренды по названию

Популярные бренды