background image

 

 

Troubleshooting the Gas Control System 

  

 

Problem 

Possible Causes 

Corrective Action 

Defective or misaligned 
electrode at pilot. 

Check for spark at electrode and pilot: if no spark and electrode wire is 
properly connected, replace igniter. 

Spark igniter will not light. 

Defective igniter (push-
button). 

Using a match, light pilot. If pilot lights, turn off pilot and push the red button 
again. If pilot will not light - check gap at electrode and pilot should be 1/8" to 
1/4" to have a strong spark. 

Defective thermocouple 
(flame switch where 
applicable). 

Check pilot flame. Must impinge on generator and thermocouple. Clean 
and/or adjust pilot for maximum flame impingement on generator and 
thermocouple. Replace thermocouple if pilot will not hold. (Hand tight 1/8 turn 
on replacement) 

Pilot will not stay lit after 
carefully following lighting 
instructions. 

Defective valve magnet. 

Replace valve, if pilot won't hold after the thermocouple is replaced. 

Wall switch or wires 
defective. 

Check wall switch and wires for proper connections. Jumper wire across 
terminals at wall switch. If burner comes on, replace defective wall switch. If 
okay, jumper wires, across wall switch wires at valve. If burner comes on, 
wires are faulty or connections are bad. 

Generator may not be 
generating sufficient voltage. 

Check generator with millivolt meter. Take reading at generator terminals of 
gas valve. Should read 325 millivolts minimum while holding valve knob 
depressed in pilot position and wall switch "off" Replace faulty generator if 
reading is below specified minimum. 

Plugged burner orifice. 

Check burner orifice for stoppage and remove. 

Pilot burning, no gas to 
burner, valve knob “ON”, 
and wall switch “ON”. 

Defective automatic valve 
operator. 

Remove wall switch wires from gas valve. Install jumper wires from top bottom 
terminals of gas valve. Turn valve on "ON". If main burner does not light, 
replace valve. 

Frequent pilot outage 
problem. 

Pilot flame may be too low or 
blowing (high) causing the 
pilot safety to drop out. 

Clean and/or adjust pilot flame for maximum flame impingement on generator 
and thermocouple. 

Flame lifts off burner and 
goes out in less than 30 
seconds. 

The inner liner has come off 
flue or termination, flame is 
starving for oxygen. 

Attach the inner liner to flue or termination using screws, silicone and clamps 
as stated in manual. 

Flame lifts off burner on 
one side while the rest of 
the flame remains lit. 

Improper installation of 
firebrick. Firebrick is likely 
leaning. 

Be sure to position firebrick against firebox walls and be sure to use brick clips 
attached to the inner side of firebox. 

 

  

WARNING

 

BEFORE DOING ANY GAS CONTROL SERVICE WORK, REMOVE THE GLASS FRONT. Before troubleshooting the 
gas control system, be sure external gas shut off is in the "On" position. 

28

Содержание FV200NE






























Отзывы: