background image

ASSEMBLY and INSTALLATION continued...

 

4

 

 

12.

 

With the holes lined the same as 

Figure 13 

you can now slide the end bow joiners and 
the main bow joiner (Part N°3) onto the 
two frame assemblies. 

Note:

 

The center 

joiner must be sitting on top of the fabric 
Figure 14

 

13.

 

Take the four 3mm flat bar pieces and slide 
them down each side of the center pocket 
making sure that the holes line up with the 
cutouts. 

Figure 15 & 16

 

14.

 

Using a 4mm drill bit drill out the inner 
tube to match the holes in the joining tubes 
(Part N°3 & 6). Bolt the two end bows to-
gether using the 4mm x 30mm button head 
screws 

from bag C. 

Figure 17  Note:

 

Make 

sure the heads of the bolts are on the out-
side of the frame. Figure 18 

 

15.

 

Using the 4mm x 40 button head screws 

from bag C

 bolt the center joiner together. 

Making sure to go through both pieces of 
3mm flat bar. 

Figure 19  

NOTE: LEAVE 

BOLTS LOOSE 

 

 

16.

 

Lubricate the four legs with the supplied 
silicone wipes. 

Figure 20

 

 

Canopy assembly will be competed 

once installed on the boat.

 

Figure 13 

Main Bow Joiner

 

3

 

Figure 13 

Bimini Laid Out

 

End Bow Holes

 

End Bow Holes

 

Main Bow Holes

 

Figure 15 

Inserting Flat Bar

 

Figure 16 

Flat Bar Holes

 

Figure 17 

Bolting End Bows

 

Figure 19 

Main Bow Bolts

 

Leave Bolts Loose

 

Figure 18 

Bolt heads

 

Figure 20 

Silicone Wipe

 

Содержание ECLIPSE








Отзывы: