ADJUSTMENTS & OPERATION
FIGURE 6
FIGURE 7
FIGURE 8
ADJUSTMENTS
Angled cuts- Adjusting bevel angle
This Plunge Cut Track Saw can be tilted for angular cuts from 0
0
to 48
0
.
1) Make sure the Plunge Cut Track Saw is disconnected from the power source.
2) Loosen the front bevel lock knob (A) Fig.6 and the rear bevel lock knob (B). Tilt
the saw until the pointer (C) lines up with your desired cutting angle on the
bevel scale (D). Retighten both bevel lock knobs.
3) The bevel pointer (C) Fig.6 is set properly at the factory. After prolonged usage,
if the pointer is not accurate, it should be adjusted properly. Make a test cut,
verify the bevel angle, if an adjustment is needed, loosen pointer screw and
reposition the pointer. Retighten screw once adjustment is made.
Blade kerf alignment indicator(s)
This Plunge Cut Track Saw comes with two blade kerf alignment indicators
(notches) on the base of the saw. These notches are designed to help you align
your cuts with your workpiece. Mark your workpiece with a cut line.
If using this Plunge Cut Track Saw without a track
, align the “0” mark (A) Fig.7
with the cut line mark you made on your workpiece for all straight cuts. For 45
0
bevel cuts, align the “45” mark (B) Fig.7 with the cut line mark you made on your
workpiece.
If using this Plunge Cut Track Saw with a track
, align the “0” mark (A) Fig.7
with the cut line mark you made on your workpiece.
Note: Blade thickness may vary, it is recommended to make tests along a cut line
to determine if the alignment notches are adequate guides to use.
Assembly & adjustment of Optional 50” track (Mod. KW-300)
IMPORTANT! THIS PLUNGE CUT TRACK SAW DOESN’T COME WITH A 50”
TRACK, TRACK CONNECTOR KIT OR A TRACK CLAMPS KIT. These
optional accessories can be purchased separately, visit your local
distributor of King Canada products or visit our web site at kingcanada.com
for more information.
List of available accessories:
Model KW-300- 50” Track
Model KW-301- Storage bag for up to two 50” tracks
Model KW-302- Track connector kit
Model KW-303- 2 Pc. Clamp kit
This Plunge Cut Track Saw can be used with one or more than one 50” track, this
will depend on the length of cuts needed. If you purchase two 50” tracks
(KW-300), you will also need to purchase the Track Connector Kit (KW-303) to
assemble them together. Follow these instruction for assembling two 50” tracks
together:
1) The Track Connector Kit (KW-303) comes with two spacer bars (A) Fig.8, and
two locking bars (B) with 4 set screws (C & D).
2) Position one spacer bar over a locking bar, insert the pin (E) of the locking bar
into the hole (F) in the spacer bar to lock them together. Make sure the spacer
bar is positioned on the opposite side of the set screws.
3) Slide the track connector assembly (A & B) Fig.8 into the groove on the rear
edge of the track (G). Make sure the set screws (C) are accessible from the top
of the track. Only slide the bars halfway as shown.
4) Tighten the two set screws (C) Fig.8 using the 3mm hex. key (supplied with
track connector kit Mod. KW-302) to secure that half of the bars to the track.
5) Repeat steps 2 to 4 for the second set of bars (A) Fig.9. Slide this set of bars
into the groove underneath the track as shown. Make sure the set screws are
accessible from the top of the track (underneath track). Only slide the bars
halfway.
6) Tighten the two set screws under the track using the 3mm hex. key (supplied
with track connector kit Mod. KW-302) to secure that half of the bars to the
track.
7) Align the bars installed to the first track, with the grooves of the second track
and slide them in all the way, see Fig.9. Secure both tracks together by
tightening all remaining set screws (D) using the 3mm hex. key (supplied with
track connector kit Mod. KW-302) to secure both tracks together.
FIGURE 9
