background image

To ensure that the release of fibres from these R.C.F (Refractory Ceramic
Fibre) articles is kept to a minimum, during installation and servicing we 
recommend that you use a HEPA filtered vacuum to remove any dust 
accumulated in and around the appliance before and after working on the 
appliance.  When replacing these articles we recommend that the replaced
items are not broken up, but are sealed within heavy duty polythene bags,
clearly labelled as “RCF waste”.  RCF waste is classed as a “stable”, non
reactive hazardous waste and may be disposed of at a landfill licensed to
accept such waste   Protective clothing is not required when handling these
articles, but we recommend you follow the normal hygiene rules of not
smoking, eating or drinking in the work area, and always wash your hands
before eating or drinking.

3.2

LIGHTING THE APPLIANCE

a)

Turn on the gas isolation tap.

b)

Depress the control knob and turn anti-clockwise to the position 
marked pilot.  Hold in the control knob for a few seconds to purge the 
pipe work.

c)

Continue to hold-in the control knob and press the igniter button.  If the 
burner does not light, continue to press the igniter button until ignition 
occurs. Continue to hold the control knob for 5-10 seconds to allow the
thermocouple to heat up, if the pilot goes out when the control knob is 
released, repeat the lighting sequence.

d)

Turn the control knob in the anti-clockwise direction to the high position 
and the main burner will light.

e)

Turn the control knob clockwise to the low position and the gas input 
will be reduced to the minimum setting.

f)

Slightly depress the control knob and turn to the pilot position, the main 
burner will go out but the pilot will remain lit.

g)

Slightly depress the control knob and turn to the off position, the pilot 
will now be extinguished.

WARNING : If the fire goes out for any reason or is turned off and it 

is necessary to re-light the fire it is important to allow the 
fire to cool for 3 minutes before attempting to re-light it.

21

Содержание KRTC00MN



























Отзывы: