Majestic ASH36 Installation Manual Download

Page: 1 / 44

Majestic • Ashland ASH36 Installation Manual • 4059-909 • Rev D • 04/19

WOODBURNING FIREPLACE

Model(s):

Installation Manual

Installation and Fireplace Setup

WARNING

HOT SURFACES

Glass and other surfaces are hot during

operation AND cool down.

Hot glass will cause burns.

•

DO NOT

touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

fireplace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable

materials.

• Keep clothing, furniture, draperies and other flammable

materials away.

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

ASH36

NOTICE:

DO NOT

discard this manual!

•

DO NOT

store or use gasoline or other flam

mable vapors and liquids in the vicinity of this

or any other appliance.

• DO NOT

overfire. Overfiring will void your

warranty.

• Comply with all minimum clearances to com-

bustibles as specified. Failure to comply may

cause house fire.

WARNING: If the information in these

instructions is not followed exactly, a fire

or explosion may result causing property

damage, personal injury, or death.

This fireplace uses SL1100 Series Chimney

2” CLEARANCE TO COMBUSTIBLES AND BUILDING INSULATION FROM CHIMNEY REQUIRED.

Fire Risk.

WARNING

For use with solid wood fuel only.

Other fuels may overfire and generate poisonous

gases (i.e. carbon monoxide).

Installation and service of this appliance should be performed by

qualified personnel. Hearth & Home Technologies recomends HHT

Factory Trained or NFI certified professionals.

Summary of Contents for ASH36













































Search results

Summary of Contents for ASH36

Reviews:

Related manuals for ASH36

Brands by name

Popular brands

Majestic ASH36, Installation Manual

Search results

Summary of Contents for ASH36

Reviews:

Related manuals for ASH36

Brands by name

Popular brands