manualshive.com logo in svg

kincrome K15320, Инструкция по эксплуатации и технике безопасности

Поделиться
Скачать
kincrome K15320 Скачать руководство пользователя страница 18

To replace the belt (Fig. 21)

Belt tension and bench drill press speed is
controlled by automatic adjustments made to the
diameter of the front spindle when the drive
handle is moved.

Note: See page 23 for information on the variable
speed function of this bench drill press. 

1.

Remove the screw that secures the housing
cover (1). Open the housing cover.

2.

Remove the belt (2) from the housing cover if
it is broken. If it is not broken, but is too
stretched to operate correctly, work the belt off
the drive (motor) spindle (3). Then remove the
belt from the front spindle (4).

3.

Replace the belt by putting a new belt over the front spindle (4) and carefully sliding the belt
over the drive (motor) spindle (3).

VI. Assembly and adjustments ... continued

18

Fig. 21

1

4

2

3

WARNING: 

DISCONNECT THE BENCH DRILL PRESS FROM THE POWER SOURCE

BEFORE REPLACING THE BELT.

WARNING: 

DO NOT CHANGE THE DRIVE SPEED WHEN THE BENCH DRILL PRESS

IS TURNED OFF.

Содержание K15320






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды