Kimball Fluent Series Скачать руководство пользователя страница 7

Страница: 7 / 25

Assembly Instructions

Fluent

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.

If you have any questions concerning these instructions, please call Kimball Office Customer Service.

Part No. 2205353

Revision A-09

Page 1 of 2

Drawer Removal, Adjustment,
and Unit Leveling

Tools Required

Installation

1. For Desk, Credenza, Return, Bridge, Lateral File & Drawer

or Door Storage: Remove all drawers as required to access

leveling glide adjustment holes.

2. To remove drawers: Extend the box or file drawer to its

full extension. Locate the drawer slide release tab, in the

approximate location shown, on each side of the drawer

box. Press both tabs in and pull drawer straight out until

slide drawer members disengage from cabinet members.

(Figure A).

3. To remove lateral file drawers, extend the drawer forward.

Press the two quick-disconnect release tabs and lift the

drawer off the slide assembly. (Figure B).

Note:

Shipping screws must be removed from drawer

suspensions before drawer can be removed.

4. Turn the leveling glides fully “in” (counterclockwise) prior

to leveling. Level the unit from front to back by first

extending the glides on the outside corners (turn clockwise),

then level the unit from side to side. Check adjustments by

placing the level at the four positions shown. Adjust inside

glides, if applicable, to help support the unit. (Figure C).

5. Replace all drawers to their original locations. To re-install,

fully extend cabinet slide members, making sure the chrome

ball-bearing members are also forward. Carefully align

drawer slide members with cabinet slide members and

gently push drawer closed. Check for proper alignment by

inspecting drawer front margins for spacing and squareness.

Figure A

Figure B

Release
Tabs

Figure C

Leveling
Glides

⁄

Nut
Driver

Level; Check
at four locations

Release
Tabs

Tape Measure

⁄

" Nutdriver

Level

Phillips Screwdriver

⁄

" Allen Wrench

⁄

" Allen Wrench

Содержание Fluent Series


























Результаты поиска

Содержание Fluent Series

Отзывы:

Бренды по названию

Популярные бренды

Kimball Fluent Series, Руководство по сборке

Результаты поиска

Содержание Fluent Series

Отзывы:

Бренды по названию

Популярные бренды