manualshive.com logo in svg

Kimball Fluent Series, Руководство по сборке

Поделиться
Скачать
Kimball Fluent Series Скачать руководство пользователя страница 2

Fluent

®

 

1  

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent. 
If you have any questions concerning these instructions, please call Kimball Office Customer Care. 

Part #2205351, Revision C 

Assembly Instructions 

Leg & Pedestal to Worksurface 

Tools Required 

Hardware Required 

• 

Pencil 

• 

Tape Measure 

• 

Screw Gun 

Leg Assembly to Worksurface

 

Note: 

It is recommended that two (2) persons be used to lift 

and flip worksurfaces. 

1.  Place the worksurface on a clean, soft surface, underside 

facing up. Align leg assembly centered front to back and 
flush with outside worksurface edge. (Figure A). Drill pilot 
holes to insure legs are mounted perpendicular to surface. 
Attach legs using fourteen (14) #10 x 1” panhead screws 
provided. (Figure B). 

2.  If using low storage support legs with a low storage unit, 

cut two pieces of double-sided adhesive tape and place on 
bottom of legs. DO NOT REMOVE film backer exposing 
adhesive at this time. (Figure C). 

Note: 

The top surface of the low storage unit MUST be clean, 

dry, and free of any dirt or residue to assure adequate adhe-
sion. 

 

Caution: 

The tape is a very strong adhesive and bonds in-

stantly to any surface it is applied.

 

Installation 

Leg Assembly 

• 

#10 x 1” Panhead Screw 

• 

Double Sided Adhesive 

Figure A 

Figure B 

Figure C 

• 

#2 Phillips Head Bit 

• 

5/32” Drill Bit 

 

Pedestal 

• 

Pedestal Spacer 

• 

#8 x 2 1/2” Flathead 
Screw 

Leg Assembly 

Low Storage 
Support Legs 

Desk-Height 
Support Legs 

Flush 

Worksurface 

Pre-Drill Pilot 
Holes Prior to 
Fastening 
screws. 

Double Sided Tape 
(Do not remove film 
backer at this time) 

Содержание Fluent Series


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды