Kidde Fire Protection SIRIUS Скачать руководство пользователя страница 35

Страница: 35 / 39

TM0066

Page 35 of 39

Issue 2.01

5.5

32 ZONE PANEL

TERMINALS

Note

All terminals are capable of accepting conductors of cross
sectional area 1.0 - 2.5 mm.

Mains Block

Live, neutral and earth 240V a.c.+ 10%/- 15%, 50/60Hz

Common Fault Relay 1

Single pole changeover rated at 30V 1 Amp.

Common Fault Relay 2

Single pole changeover rated at 30V 1 Amp.

Common Fire Relay 1

Single pole changeover rated at 30V 1 Amp.

Common Fire Relay 2

Single pole changeover rated at 30V 1Amp.

Common Fire Relay 3

Single pole changeover rated at 30V 1 Amp.

Common Fire Relay 4

Single pole changeover rated at 30V 1Amp.

Auxillary Reset Relay

Single pole changeover relay rated at 30V 1 Amp, operates
for 5 seconds after panel reset.

Auxillary Supply

0V and 24V d.c. output terminals rated at 750 mA.

Sounder Circuit 1

Reverse polarity monitored circuit rated at 1000 mA.

Sounder Circuit 2

Reverse polarity monitored circuit rated at 1000 mA.

Sounder Circuit 3

Reverse polarity monitored circuit rated at 1000 mA.

Sounder Circuit 4

Reverse polarity monitored circuit rated at 1000 mA.

Repeat Outputs

Common fault and zones 1 - 32 repeat rated at 100 mA.

Remote Inputs

Evacuate, silence and reset terminals which require a 0V to
activate them.

User LEDs 1- 4

0V input required to activate the LEDs located on the
membrane.

Zones 1 - 32

+ & - per zone, each rated at 5 mA with a maximum of 20
detectors per zone.

Battery

+ & - input terminals which can receive a maximum of 1000
mA from the charger.

Fault Input

0V input requires to drive common fault indication.

Evac. Output

0V output to sound alarms mode.

Silence Output

0V output to silence alarms mode.

Reset Output

0V output in Reset mode.

NOTE:

The remote inputs and outputs are for internal use only.

Содержание SIRIUS








































Результаты поиска

Содержание SIRIUS

Отзывы:

Похожие инструкции для SIRIUS

Бренды по названию

Популярные бренды

Kidde Fire Protection SIRIUS, Руководство пользователя

Результаты поиска

Содержание SIRIUS

Отзывы:

Похожие инструкции для SIRIUS

Бренды по названию

Популярные бренды