manualshive.com logo in svg

Keysight U4421A, Руководство по аппаратному обеспечению и пробам

Поделиться
Скачать
Keysight U4421A Скачать руководство пользователя страница 3

Keysight U4421A MIPI D-PHY Analyzer and Exerciser Hardware and Probing Guide

3

 

Safety Summary

Safety Symbols on

Instruments

General Safety

Precautions

The following general safety precautions must be observed during all phases of operation of this 

instrument. Failure to comply with these precautions or with specific warnings elsewhere in this 

manual violates safety standards of design, manufacture, and intended use of the instrument.
Keysight Technologies Inc. assumes no liability for the customer's failure to comply with these 

requirements.
Before operation, review the instrument and manual for safety markings and instructions. You must 

follow these to ensure safe operation and to maintain the instrument in safe condition.

General

This product is a Safety Class 1 instrument (provided with a protective earth terminal). The protective 

features of this product may be impaired if it is used in a manner not specified in the operation 

instructions.
All Light Emitting Diodes (LEDs) used in this product are Class 1 LEDs as per IEC 60825-1.

Environment

Conditions

This instrument is intended for indoor use in an installation category II, pollution degree 2 

environment. It is designed to operate at a maximum relative humidity of 95% and at altitudes of up 

to 2000 meters.
Refer to the specifications tables for the ac mains voltage requirements and ambient operating 

temperature range.

Before Applying

Power

Verify that all safety precautions are taken. The power cable inlet of the instrument serves as a device 

to disconnect from the mains in case of hazard. The instrument must be positioned so that the 

operator can easily access the power cable inlet. When the instrument is rack mounted the rack 

must be provided with an easily accessible mains switch.

Safety Symbol

Description

Indicates warning or caution. If you see this symbol on a product, you must refer to the manuals for 
specific Warning or Caution information to avoid personal injury or damage to the product.

Frame or chassis ground terminal. Typically connects to the equipment's metal frame.

Indicates hazardous voltages and potential for electrical shock.

Indicates that anti static precautions should be taken.

Indicates hot surface. Please do not touch.

Indicates laser radiation turned on.

CSA is the Canadian certification mark to demonstrate compliance with the Safety requirements.

CE compliance marking to the EU Safety and EMC Directives.
ISM GRP-1A classification according to the international EMC standard.
ICES/NMB-001 compliance marking to the Canadian EMC standard.

Содержание U4421A

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды