manualshive.com logo in svg

Keysight U4421A, Руководство по аппаратному обеспечению и пробам

Поделиться
Скачать
Keysight U4421A Скачать руководство пользователя страница 19

Keysight U4421A MIPI D-PHY Analyzer and Exerciser 

Hardware and Probing Guide

3

Determining the Extent of 

Signal Degradation with 

Acquisition Probes

Before you start designing the setup for a particular acquisition probing solution that you plan to use 

with U4421A module, you should simulate the signal integrity with that probing solution. This helps 

you assess the extent of signal degradation in a specific target system on attaching the probes to 

signals in that target system. 

Some extent of signal degradation is always present. To determine if this signal degradation is 

significant in a specific target system, you should run a simulation with the probe loads for the 

probing method(s) to be used.

The amount of signal degradation that a target system can tolerate can vary widely depending on 

signal rise times, design margins and system noise. 

The following table provides some guidelines for the acquisition probing method used for U4421A 

module vs. bit rate assuming a "typical" target system (Note that this includes the effect of two 

probes per signal):

\\

Probe

Attachment

Maximum Bit Rate

E5405A Soft Touch

Connectorless

>1.5 Gbps

E5381A Flying Leads

Coaxial Tip Resistors (82 Ohms)

>1.5 Gbps

E5381A Flying Leads

3-Pin Headers

1.0 Gbps

E5381A Flying Leads

Socket Adapters

1.0 Gbps

E5381A Flying Leads

Damped Wires (160 Ohms)

0.8 Gbps

NOTE

When the E5381A or E5405A probe is used with the U4421A module, each 

signal is probed twice. Therefore, when simulating the electrical impact of these 

probes, you must attach two probe loads to each signal. 

Содержание U4421A

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды