manualshive.com logo in svg

Keysight U4421A, Руководство по аппаратному обеспечению и пробам

Поделиться
Скачать
Keysight U4421A Скачать руководство пользователя страница 29

Keysight U4421A MIPI D-PHY Analyzer and Exerciser Hardware and Probing Guide

29

Setting up an E5381A Differential Flying Lead Probe Configuration for U4421A Module

4

Based on the number assigned to each flying lead (see 

Figure 7

), the following table lists which flying 

lead of the probe to be used to probe different D-PHY signals.

Signal to be probed

Flying Lead to be used

Notes/Usage of flying lead

Clkp 

Ch 13 

Connect the Positive (Light grey) cable of the flying lead to acquire signal.
Connect the Negative (Dark grey) cable of the flying lead to ground.

Clkn 

Ch 15

Connect the Positive (Light grey) cable of the flying lead to acquire signal.
Connect the Negative (Dark grey) cable of the flying lead to ground.

Clk diff

Ch 14

Connect the Positive (Light grey) cable of the flying lead to the Clkp signal and 
Negative (Dark grey) cable of the flying lead to the Clkn signal.

Data Lane 0 p

Ch 0 

Connect the Positive (Light grey) cable of the flying lead to acquire signal.
Connect the Negative (Dark grey) cable of the flying lead to ground.

Data Lane 0 n

Ch 2

Connect the Positive (Light grey) cable of the flying lead to acquire signal.
Connect the Negative (Dark grey) cable of the flying lead to ground.

Data Lane 0 diff

Ch 1

Probe differentially 
Connect the Positive (Light grey) cable of the flying lead to the D0p signal and 
Negative (Dark grey) cable of the flying lead to the D0n signal.

Data Lane 1

Ch 4

Probe differentially
Connect the Positive (Light grey) cable of the flying lead to the D1p signal and 
Negative (Dark grey) cable of the flying lead to the D1n signal.

Data Lane 2

Ch 8

Probe differentially
Connect the Positive (Light grey) cable of the flying lead to the D2p signal and 
Negative (Dark grey) cable of the flying lead to the D2n signal.

Data Lane 3

Ch 11

Probe differentially
Connect the Positive (Light grey) cable of the flying lead to the D3p signal and 
Negative (Dark grey) cable of the flying lead to the D3n signal.

NOTE

The Data Lane 0p, Data Lane 0n, Clkp, and Clkn signals are probed both as 

single-ended and differential. This is done to allow the U4421A module to detect 

LP and HS modes. When probed as single-ended, you must connect the 

negative sides of the single-ended connections to ground.
The Data Lane 1, 2, and 3 each are probed differentially using a single channel 

per data lane used.
The U4421A module can capture LP data and display it in "raw" mode on these 

data lanes. If you want to capture LP data on these lanes, then you must probe 

these lanes single-ended using the following signal to probe’s channel mapping:
D1p - Ch 3 
D1n - Ch 5
D2p - Clk
D2n - Ch 9
D3p - Ch 10
D3n - Ch 12

Содержание U4421A

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды