11
Upgrade kits are available to add options after initial purchase. To order
an upgrade kit for the PNA series, order the analyzer’s model number fol-
lowed by a “U”, then indicate the option to be added
(for example, E8362CU-010). The current configuration and serial num-
ber of the instrument to be retrofitted are required as part of
the order.
□
Time-domain (Option 010)
User installable.
□
Configurable test set (Option 014)
Provides six front-panel RF access loops.
Includes installation at a Keysight service center.
□
Receiver attenuators (Option 016)
Includes installation at a Keysight service center.
□
Frequency range upgrade to an E8363C
(40 GHz) PNA (Option 040/041)
Available only for the E8362C. Includes
installation at a Keysight service center.
□
Frequency range upgrade to an E8364C
(50 GHz) PNA (Option 050/051)
Available only for the E8362C and E8363C.
Includes installation at a Keysight service center.
□
Frequency range upgrade to an E8361C
(67 GHz) PNA (Option 067/068)
Available only for the E8363C and E8364C.
Includes installation at a Keysight service center.
□
Frequency-offset (Option 080)
Includes installation at a Keysight service center.
□
External reference switch (Option 081)
Includes installation at a Keysight service center.
□
Scalar-calibrated converter measurements
(Option 082)
User installable. Option 080 required.
□
Frequency converter measurement
application (Option 083)
User installable. Option 080 and 081 required.
□
Embedded LO Measurements (Option 084)
Advanced software tuning that provides absolute group delay of
converters with embedded LOs without the need for access to a
common reference signal. The measurement result is the same as
locking the DUT LO to the reference mixer LO. (Options 080
and 083 required) Requires firmware A.07.05 and above plus
1.1 GHz CPU board.
v
A/B to C model upgrades
Order E8361AU-221, E8362BU-221, E8363BU-221, or E8364BU-221
Note:
1. GHz CPU is required to upgrade. Please refer to Customer Support
Service Guides for the correct part number http://na.tm.keysight.com/
pna/documents.html
□
4-Port measurement application (Option 550)
(Available for E8361C, E8362C/3C/4C)
Enables full 4-port error correction and differential
measurements. Option 014 and external test set required.
User installable.
□
N-port capabilities (Option 551)
(Available for E8361C, E8362C/3C/4C)
Adds full N-port error correction and measurement
capabilities. Option 014 and external test set required.
User installable.
□
Extended power range (Option UNL)
Adds a step attenuator and a bias-tee between source and
each test port. Includes installation at a Keysight service center.
□
Pulsed-RF measurement capability
(Option H08)
Provides software to set up and control pulsed-RF
measurements using narrowband detection, with point-in-pulse
and pulse-profile capability. User installable.
□
IF access (Option H11)
Provides hardware for antenna, point-in-pulse, and millimeter-
wave measurements. Adds rear-panel RF and LO outputs,
external IF inputs, and IF gates (gates enabled with Option H08).
Includes installation at a Keysight service center.
□
High-power test set (Option H85)
Removes bias tees for higher test port power-handling capability.
Options UNL, 014, 016, 080, and 081 are required. Includes
installation at a Keysight Service Center.
Calibration Software Licenses
□
Perpetual license for built-in performance
test software for Keysight inclusive cal
(Option 897)
Adds built-in performance testing and calibration software
for self-maintainers. Requires additional equipment. See
the analyzer’s Service Guide for more information on
equipment required.
□
Perpetual license for built-in performance
test software for standards compliant cal
(Option 898)
Adds built-in performance testing and calibration software
for self-maintainers. Requires additional equipment. See
the analyzer’s Service Guide for more information on
equipment required.
PNA Series Network Analyzer (continued)
Upgrade kits
Upgrade kits for the PNA Series E8361C, E8362C, E8363C, E8364C
1. Note: For applications, measurement accessories, and general
accessories please see Keysight PNA Family Network Analyzers
Configuration Guide, part number 5990-7745EN.
