Keysight N5281A Скачать руководство пользователя страница 37

Страница: 37 / 56

User’s and Service Guide N5281-90001

N5281A

Operational Check

N5245A Operational Check Procedure

The sequence of this procedure is very important and must be followed or the performance

accuracy and results may vary from the reference plots provided.

If you are using a N5244A or N5245A 2-Port PNA-X, channels C and D

will be replaced with R1 and R2.

The following procedures are used with the N5245A.

Preparing the N5245A

1. Connect the Test Set to the N5245A using the cables as shown in



Figure 15 on page 22

Figure 16 on page 23

and

Figure 17 on page 23

2. Connect the 10 dB attenuator to the PNA-X reference port cable.
3. Turn On the Test Set.
4. Select

[Preset]

5. Verify that the Stop Frequency is set to the maximum frequency of the PNA and test set. If

not, select

[Freq]

Stop

6. Verify that the Start Frequency is set to 10 MHz. If not, select [

Freq]

Start

[10 MHz]

7. Verify that the Power is to set to -5 dBm. If not, select

[Power]

Power Level



[-5 dBm]

8. Select

[Avg]

IF Band wid th

[1 kHz]

9. Select

[Sweep]

Number of Points

[401]

10.Allow the test set and the PNA to warm up for a minimum of 30 minutes.
11.Set the IF Switch Config On. In the drop-down menu select

Trace/Chan

Channel

Hard ware Setup

IF Switch Config

Figure 25

IF Switch Config

Содержание N5281A

























































Результаты поиска

Содержание N5281A

Отзывы:

Похожие инструкции для N5281A

Бренды по названию

Популярные бренды

Keysight N5281A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание N5281A

Отзывы:

Похожие инструкции для N5281A

Бренды по названию

Популярные бренды