manualshive.com logo in svg

Keysight N5281A, Руководство пользователя и сервисное руководство

Поделиться
Скачать
Keysight N5281A Скачать руководство пользователя страница 14

 

10

 User’s and Service Guide N5281-90001

N5281A

General Specifications

Environmental Requirements 

The environmental requirements of the test set are listed in 

Table 4

. Refer to the E8363B/C, 

E8364B/C, N5244/45A and N5264A User’s Guide for environmental specifications.

Ventilation Requirements: When installing the instrument in a cabinet, the 

convection into and out of the instrument must not be restricted. The 

ambient temperature (outside the cabinet) must be less than the 

maximum operating temperature of the instrument by 4 °C for every 100 

watts dissipated in the cabinet. If the total power dissipated in the 

cabinet is greater than 800 watts, forced convection must be used.

Environmental Tests
The N5281A complies with all applicable safety and regulatory requirements for the intended 

location of use.

Equipment Heating and Cooling
If necessary, install air conditioning and heating to maintain the ambient temperature within the 

appropriate range. Air conditioning capacity must be consistent with the BTU ratings given in 

Table 3

.

Required Conditions for Accuracy Enhanced Measurement
Accuracy–enhanced (error–corrected) measurements require the ambient temperature of the 

PNA and test set to be maintained within ± 1 °C of the ambient temperature at calibration.
The instrument can safely operate in a relative humidity of 80% for temperatures to 

31 degrees C, decreasing linearly to 50% relative humidity at 40 degrees C.

Table 4 

N5281A Operating Environment 

Temperature

Measurement Calibration      

20 °C to 26 °C (68 °F to 79 °F)

Performance Verification             

Temperature must be within 1 °C (1.8 °F) of the 
temperature at which the measurement 
calibration was performed.

Pressure Altitude           

(Operation or Storage) 

0 to 3,000 meters (~10,000 feet)

Содержание N5281A

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды