Keysight N5281A Скачать руководство пользователя страница 13

Страница: 13 / 56

User’s and Service Guide N5281-90001

N5281A

General Specifications

Power Requirements

Verify that the required ac power is available before installing the test set to the network

analyzer.

• 100/120/220/240 V (50/60 Hz)
• The instruments can operate with mains supply voltage fluctuations up to ± 10% of



the nominal voltage.

• Air conditioning equipment (or other motor–operated equipment) should not be placed on

the same ac line that powers the test set and PNA.

•

Table 3

contains the maximum wattage for all instruments. This table can be use to

determine the electrical and cooling requirements.



This is a Safety Class I product (provided with a protective earthing

ground incorporated in the power cord). The mains plug shall be

inserted only into a socket outlet provided with a protective earth

contact. Any interruption of the protective conductor, inside or outside

the instrument, is likely to make the instrument dangerous. Intentional

interruption is prohibited.

Table 3

Power Requirements

Standard Equipment

Instrument

Maximum

Wattage

E8363B/C

350

E8364B/C

350

N5244A

450

N5245A

450

N5264A

450

N5281A

350

Содержание N5281A

























































Результаты поиска

Содержание N5281A

Отзывы:

Похожие инструкции для N5281A

Бренды по названию

Популярные бренды

Keysight N5281A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание N5281A

Отзывы:

Похожие инструкции для N5281A

Бренды по названию

Популярные бренды