Keysight 87406Q Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 37

background image

Installation and Verification

4

Keysight 87406Q Operating and Service Manual

31

Operating and Service Instruction

Operator’s check

The operator’s check is supplied to allow the operator to make a
quick check on the switch prior to use or if a failure is suspected.

Description

The coaxial matrix switch is connected to a network analyzer
configured for the S- parameter measurement. The network
analyzer may be set to sweep over the whole or selected frequency
range of the switch to be verified. The S- parameter measurement
is the best way to determine if the switch is working properly.

C A U T I O N

ESD exceeding the level specified in

“Environmental specifications”

or RF

power applied is greater than the maximum specified as in

“General

Specifications”

may cause permanent damage to the device.

Figure 4-1

Connection to perform quick check

NETWORK ANALYZER

C

Keysight Coaxial

Transfer Switch

Port 1

Port 2

POWER SUPPLY

«
...
31
32
33
34
35
...
»

Содержание 87406Q






































Отзывы:

Нет отзывов

Похожие инструкции для 87406Q

Бренд: JDS Uniphase Страницы: 40

Бренд: Gefen Страницы: 11

xStack DES-3500 Series

Бренд: D-Link Страницы: 260

DXS-3600 Series

Бренд: D-Link Страницы: 48

DXS-3400 SERIES

Бренд: D-Link Страницы: 3

Web Smart Switch DGS-1210-16

Бренд: D-Link Страницы: 71

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 56

xStack DES-3800 Series

Бренд: D-Link Страницы: 326

xStack DES-3526

Бренд: D-Link Страницы: 222

Бренд: D-Link Страницы: 2

DXS-1210 Series

Бренд: D-Link Страницы: 20

EasySmart DGS-1100-08

Бренд: D-Link Страницы: 44

Бренд: pathway Страницы: 28

Бренд: GE Страницы: 302

Бренд: IBM Страницы: 44

Бренд: AAVARA Страницы: 23

Бренд: EtherWAN Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды