Keysight Technologies U4431A Скачать руководство пользователя страница 34

Страница: 34 / 40

Setting up a U4432A SMA Differential Probe Configuration

Keysight U4431A MIPI M-PHY Protocol Analyzer Hardware and Probing Guide

Labeling and Color Coding of Coaxial Cables

To help you identify the appropriate coaxial cable to use in a given situation, the coaxial cables of the

U4432A probe are labeled and color coded.

The following table lists the label, color coding, and pin number mapping of each of these coaxial

cables.

NOTE

In addition to the M-PHY data lines, the probe also provides a reference clock to the DUT.

However, currently, the U4431A module does not support receiving or supplying an external

reference clock.

Label

Color Coding

Pin Number

Refn

Red with white

Refp

Red 7

TX0n

White with white

TX0p

White

RX0n

Black with white

RX0p

Black

TX1n

Violet with white

TX1p

Violet

RX1n

Blue with white

RX1p

Blue

TX2n

Yellow with white

TX2p

Yellow

RX2n

Orange with white

RX2p

Orange

TX3n

Grey with white

TX3p

Grey

RX3n

Green with white

RX3p

Green

Clkp

Brown 38

Clkn

Brown with white

Vsense

Содержание U4431A









































Результаты поиска

Содержание U4431A

Отзывы:

Похожие инструкции для U4431A

Бренды по названию

Популярные бренды

Keysight Technologies U4431A, Руководство по аппаратному обеспечению и пробам

Результаты поиска

Содержание U4431A

Отзывы:

Похожие инструкции для U4431A

Бренды по названию

Популярные бренды