Keysight Technologies S8780A Скачать руководство пользователя страница 105

Страница: 105 / 117

Getting Started Guide 105

Test Set Operating System
System Maintenance

Hard Drive Recovery Process

The Keysight Recovery System can be used to repair errors on the test set's

drive partition, or to restore the original factory configuration of the system

software. The Keysight Recovery System is stored in a separate hidden hard

disk drive partition.
Repairing errors on the hard disk drive may result in loss of data or files. If you

need more information about the Windows “chkdsk” error repair process, see

the chkdsk documentation in the Microsoft Windows Help and Support Center.
Restoring the original factory system software does not restore any of the

following items:

— Windows system configurations that were made after the test set was

shipped from the factory. For example, Windows and Service Pack updates,

user accounts, and Windows configuration settings. After an Keysight

Recovery, these configurations need to be redone.

— Additional software that was installed after the test set was shipped from

the factory. After an Keysight Recovery, that software needs to be

re-installed.

— Any data or programs saved on the

drives.

— Any upgrades that were made to the Keysight measurement application

software.

Restoring the original factory system software will not synchronize the code in

the Field Programmable Gate Arrays (FPGAs) on the various hardware

assemblies. As a result, you may see an error dialog box appear during the final

boot-up at the end of the recovery process. This typically occurs when there

are significant differences between the software version installed prior to

performing the recovery and the version restored by the recovery. In these

situations, upgrade the software to the latest version.

It is recommended that routine backups of the test set information be

performed to keep current archives of the test set information. This allows a full

recovery of the test set information after the test set recovery system

operations are performed. See

“Hard Drive Partitioning and Use” on

page 104

for more details.

It is recommended that you use a regular back up strategy. Your IT department

may already have a back up strategy in place which is suitable for the test set and
its data. See

“Hard Drive Partitioning and Use” on page 104

. Using

the Keysight Recovery System in conjunction with a regular back up strategy

should allow you to fully recover the test set software and data.

Содержание S8780A






















































































































Результаты поиска

Содержание S8780A

Отзывы:

Похожие инструкции для S8780A

Бренды по названию

Популярные бренды

Keysight Technologies S8780A, Руководство по началу работы

Результаты поиска

Содержание S8780A

Отзывы:

Похожие инструкции для S8780A

Бренды по названию

Популярные бренды