Keysight Technologies AC6801B Скачать руководство пользователя страница 164

Страница: 164 / 197

[SOURce:]VOLTage:PROGramming:SOURce INTernal|EXTAC|EXTDC
[SOURce:]VOLTage:PROGramming:SOURce?

Sets the voltage programming source.

Parameter

Typical Return

INTernal|EXTAC|EXTDC

INT, EXTAC, or EXTDC

Set the voltage programming source to external AC:
VOLT:PROG:SOUR EXTAC

The EXTAC and EXTDC modes require the analog interface card.

The

*RST

command sets this parameter to INTernal.

[SOURce:]VOLTage:RANGe[:UPPer] 155|310|MINimum|MAXimum
[SOURce:]VOLTage:RANGe[:UPPer]? [MINimum|MAXimum]

Sets the voltage range. If the voltage range is switched, the

VOLT:TRIG

and

VOLT:OFFS:TRIG

settings

are cleared, and ABORt[:ALL] is applied.

Parameter

Typical Return

155|310|MINimum|M2.02

Set the voltage range to 310 V
VOLT:RANG MAX

You may only set this parameter if output is OFF.

Setting this parameter turns voltage autoranging OFF and aborts both TRANsient and ACQuire
operations.

The

*RST

command sets this parameter to 155.

If you enter a value between 0 and 155, the 155 V range will be chosen. If you enter a value above 155
V, the 310 V range will be chosen.

[SOURce:]VOLTage:RANGe:AUTO ON|1|OFF|0
[SOURce:]VOLTage:RANGe:AUTO?

Enables or disables voltage autoranging. If this parameter changes, the

VOLT:TRIG

and

VOLT:OFFS:TRIG

settings are cleared, and all operations are aborted.

Parameter

Typical Return

ON|1|OFF|0

0 (OFF) or 1 (ON)

Turn on voltage autoranging:
VOLT:RANG:AUTO 1

The

*RST

command sets this parameter to OFF.

3 SCPI Programming Reference

164

Keysight AC6800B Series Operating and Service Guide

Содержание AC6801B






































































































































































































Результаты поиска

Содержание AC6801B

Отзывы:

Похожие инструкции для AC6801B

Бренды по названию

Популярные бренды

Keysight Technologies AC6801B, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание AC6801B

Отзывы:

Похожие инструкции для AC6801B

Бренды по названию

Популярные бренды