Keysight Technologies 85033E Скачать руководство пользователя страница 29

Страница: 29 / 52

Keysight 85033E User’s and Service Guide 3-

Use, Maintenance, and Care of the Devices
Gaging Connectors

Gaging Female 3.5 mm Connectors

Select the proper gage for your connector. Refer to

Table 6-3 on page 6-4

for gage part numbers.

Inspect and clean the gage, gage master, and device to be gaged. Refer to

“Visual Inspection” on page 3-3

and

“Cleaning Connectors” on page 3-5

earlier in this chapter.

Zero the connector gage (refer to

Figure 3-4 on page 3-13

While holding the gage by the barrel, and without turning the gage

or the device, screw the female gage connecting nut onto the

female gage master, just until you meet resistance. Connect the nut

finger-tight. Do not overtighten.

Use the torque wrench recommended for use with the kit to tighten

the connecting nut to 90 N-cm (8 in-lb). Refer to

“Connections” on

page 3-14

for more information.

As you watch the gage pointer, gently tap the barrel of the gage to

settle the reading.
The gage pointer should line up exactly with the zero mark on the

gage. If not, adjust the zero set knob until the gage pointer lines up

exactly with zero.

Remove the gage master.

Gage the device connector (refer to

Figure 3-4 on page 3-13

While holding the gage by the barrel, and without turning the gage

or the device, screw the female gage connecting nut onto the

female device being measured, just until you meet resistance.

Connect the nut finger-tight. Do not overtighten.

Use the torque wrench recommended for use with the kit to tighten

the connecting nut to 90 N-cm (8 in-lb). Refer to

“Connections” on

page 3-14

for more information.

Gently tap the barrel of the gage with your finger to settle the gage

reading.

Read the gage indicator dial. Read

only

the black



signs;



not

the

red



signs.

For maximum accuracy, measure the connector a minimum of three

times and take an average of the readings. Use different

orientations of the gage within the connector. After each

Always hold a connector gage by the gage barrel, below the dial indicator. This gives the best

stability, and improves measurement accuracy. (Cradling the gage in your hand or holding it by

the dial applies stress to the gage plunger mechanism through the dial indicator housing.)

Содержание 85033E





















































Результаты поиска

Содержание 85033E

Отзывы:

Похожие инструкции для 85033E

Бренды по названию

Популярные бренды

Keysight Technologies 85033E, Руководство пользователя и обслуживания

Результаты поиска

Содержание 85033E

Отзывы:

Похожие инструкции для 85033E

Бренды по названию

Популярные бренды