Keysight Technologies 85033E Скачать руководство пользователя страница 26

Страница: 26 / 52

Keysight 85033E User’s and Service Guide

Use, Maintenance, and Care of the Devices
Gaging Connectors

When to Gage Connectors

Gage a connector at the following times:

• Prior to using a device for the first time: record the pin depth measurement

so that it can be compared with future readings. This serves as a good

troubleshooting tool when you suspect damage may have occurred to the

device.

• If either visual inspection or electrical performance suggests that the

connector interface may be out of typical range (due to wear or damage, for

example).

• If a verification device is used by someone else or on another system or

piece of equipment.

• Initially after every 100 connections, and after that as often as experience

indicates.

Gaging Procedures

Gaging Male 3.5 mm Connectors

Select the proper gage for your connector. Refer to

Table 6-3 on page 6-4

for gage part numbers.

Inspect and clean the gage, gage master, and device to be gaged. Refer to

“Visual Inspection” on page 3-3

and

“Cleaning Connectors” on page 3-5

Zero the connector gage (refer to

Figure 3-3 on page 3-10

While holding the gage by the barrel, and without turning the gage

or the device, screw the male gage master connecting nut onto the

male gage, just until you meet resistance. Connect the nut finger

tight. Do not overtighten.

Use the torque wrench recommended for use with the kit to tighten

the connecting nut to 90 N-cm (8 in-lb). Refer to

“Connections” on

page 3-14

for more information.

As you watch the gage pointer, gently tap the barrel of the gage to

settle the reading.
The gage pointer should line up exactly with the zero mark on the

gage. If not, adjust the zero set knob until the gage pointer lines up

exactly with zero.

Remove the gage master.

Gage the device connector (refer to

Figure 3-3 on page 3-10

Always hold a connector gage by the gage barrel, below the dial indicator. This gives the best

stability, and improves measurement accuracy. (Cradling the gage in your hand or holding it by

the dial applies stress to the gage plunger mechanism through the dial indicator housing.)

Содержание 85033E





















































Результаты поиска

Содержание 85033E

Отзывы:

Похожие инструкции для 85033E

Бренды по названию

Популярные бренды

Keysight Technologies 85033E, Руководство пользователя и обслуживания

Результаты поиска

Содержание 85033E

Отзывы:

Похожие инструкции для 85033E

Бренды по названию

Популярные бренды