7
8
6-1 The preset User Code is 1234. Please delete it and create your personal code
when first time operation.
6-2 Up to 6 sets of User codes can be saved.
6-3 User Code is only for activating the lock, without programming function.
6-4
is 4-10 digits in length.
6-5
can be deleted or changed anytime if needed.
7-1 User Codes can be deleted individually. You can reset the same number as code
even it's deleted before.
7-2 You should enter Programming code to delete individual User code.
8-1 All the User Codes can be deleted at once. You can still reset the same numbers
as codes even they're deleted before.
8-2 Auto-locking and Keypad locking function will be invalid after deleting all
User Codes and the lock can only be operated by key. All the electrical functions
will be restored when recreate new User Codes.
8-3 You need to enter Programming Code to delete all User Codes.
9-1 Auto-locking and Keypad locking function will be invalid when User Codes are
temporarily disabled. The lock can only be operated by key during the time.
9-2 Repeat the programming steps again to restore the User Codes.
10-1 Disposable User Code will be no longer valid once being used.
10-2 You can reset same number as Disposal User Code.
10-3 You need to enter Programming Code to create a Disposable User Code.
11-1 You can restore Preset Factory Code by pressing “R” button on the interior
receiver module when you forget Programming Code or you want to cancel all
previous setting.
11-2 After restore, the Programming Code would be 0000; the User Code would be
1234 again.
6.User Code
7.Delete Individual User Code
8.Delete All User Codes At Once
9.Temporarily Disable All User Codes
10.Create a Disposable User Code
11.Restore Preset Factory Code
User Code
User Code
12-1 The door will be unlocked by key or pressing User Code on keypad from outside
or by interior turn-piece.
12-2 To unlock the door on the keypad, enter the User Code and then press the
Programming/Enter button.
The door will be locked by key or pressing Programming Button on keypad from
outside or by interior turn-piece.
14-1 Once the latch bolt is not extended/retracted completely and causing a not
functional motor operation when it's locked by keypad, you'll see LED flash red 3
times (for twice) and hear 3 beeps (No alarm when it's in mute). You need to
enter User Code to unlock the door for remaining the bolt retracted, and press
Programming Button to lock the door again.
14-2 If the latch bolt gets stuck or can't extend/retract completely all the time, please
check if the strike aligns with the latch bolt perfectly and adjust the strike to
proper position. After long use of the door hinge, the latch bolt might get stuck
easily because the door is deformed or lopsided.
15-1 The door will automatically lock itself within 10~99 seconds when this function
is programmed.
15-2 This function is not preset at the beginning; it can be set if needed.
15-3 The preset delay-time is 30 seconds; you can adjust the period you want.
15-4 Please repeat the same programming steps to cancel Auto-Locking function
when needed.
15-5 The system will alarm twice if the latch bolt gets stuck or not extended/retracted
completely.
You need to enter User Code to unlock the door for remaining the bolt retracted.
The auto-locking function will be restored then.
16-1 You will hear beep sounds when pressing
, programming or operating
errors. It can be turned off if needed.
16-2 LED Illumination is still functioning when it's in mute. For there will be no any
warning alarm, we suggest not to mute the beeper if it's not necessary.
16-3 Motor operating sound cannot be muted.
12.Unlock the door
13.Lock the door
14.Incomplete Door Closing / Opening
15.To Activate / Deactivate Auto-Locking Function
16.Toggle Mute On/Off
keypad
