fnox
®
INSTRUCTIONS FOR INSTALLING ED93F-CVRW
u s
A
SERIES CONCEALED VERTICAL ROD EXIT DEVICE
(6)# 1 /4"x2"
Top
Chassis
Top
Bolt
..
__
..
'
__
..
--'-�
-�\
Available stock length
- For 32" doors, Device can be cut to
fit doors down to 24" wide
- For 36" doors, Device can be cut to
fit doors down to 32" wide
- For 48" doors, Device can be cut to
fit doors down to 36" wide
(2)# 5Mx0.8x15/32"
THIS EXIT DEVICE IS HANDED
CHECK HAND OF DEVICE AGAINST APPLICATION
RIGHT HAND
REVERSE BEVEL
OUT
�
DOUBLE DOORS
LEFT HAND
REVERSE BEVEL
End Cap
Main
Chasis
Door Surface must be flush
to al low Exit Device rest
Top
�
Rod-
1
on flat surface of the door
Inner Chassis
Mounting Plate
Mounting
(2)#12x1-1/2"
D
wood
screws
�,;,4,
I
I'
I
:
.,
�
I
,,,
"'
(] @ ......
....J
-.J
,,.
.,
6l\ (},
,,,
Inner
Chassis
[f ® .... ,
..,,-"'
,,.
ij
®
��ir
®
',,
i
EJ ',��/
Rod
Bottom
Rod_
Bottom
�
Case - �
'
(2)# 3/16"x1-1/4"
wood screws
5Mx0.8x3/4"
(2)# 3/16"x1-1/4"
i ___,--
wood screws
(4)# 3/16"x1-1/4"
wood screws
1. Through Inner Chassis cutout in the door, insert the extension in the door.
2. Insert Inner Chassis in the cutout, insert reduced end of extension in top
threaded bushing on inner chassis, and fasten the rod extension with 1
machine screw.
3. On outside of door through the cutout, install Plate into extension in the door.
4. Before attaching main chassis and inner chassis to the door, attach esc lever
trim to the door with (2) 1/4-20 x 2-3/8" flat head machine screws.
5. Then attach Rail Assembly to the chassis, and hinge stile end of rail to the door
with mounting bracket.
Outside surface for Door
Inner Chassis Mounting Plate
/
Holes for
LHRB doors
1-17/3
2-29/32"
l 1r
-� - - - - - - - -a1c- =ici.=,.tt
C'sink for /
\
1/4"-20 flat
Holes for
Head Machine
LHRB doors
Screws
0.23" DIA, THRU DOOR,
Outside for 0.37"
(4 Reqd)
I
I
1-5/8"
I
<i
-r- �
I
-13/32
i
6-15/32"
I
'Tl
�
41"FROM
FINISHED
1-1/2" FLOOR
REF
I
J I
25/32" 25/32"
_J
(4)5/32"x32x1/4"
machine screws
ATTACH
OUTSIDE
TRIM IF
USED
IF AN OUTSIDE
AUXILIARY
CONTROL IS
USED, SEE THE
INSTRUCTION
SHEET PACKE
WITH THE
CONTROL
MOUNT TRIM
Mounting
Plate
MOUNTING
INSTRUCTION SHEET
PACKED WITH TRIM
1. Thru Inner Chassis cutout in the door, insert the extension in the door.
2. Insert Inner Chassis in the cutout, and insert reduced end of extension in top
threaded bushing on inner chassis, and fasten the rod extension with 1 machine
screw.
3. On outside of door through the cutout, install Plate into extension in the door.
4. Attach mounting plate to inner chassis with 2 machine screws, then attach
mounting plate to the door with 2 wood screws.
5. Attach WD Esc trim to the door. Then attach Rail Assembly to the chassis, and
hinge Stile end of rail to the door with mounting plate.
Install
Chassis
OUTSIDE FOR DOOR
OUTSIDE
INSIDE
'' '
1 ......
�so,
' ''
'
t-----
i
i
1,::T��
Install for Door
Top Rod
i
0
Plate
Extension
Bottom Rod
/ (1) Machine screw
/
5Mx0.8x1/2"
'-�
'�- (2) wood screw
3/16"x1-1/4" (2)
ED93
INSTRUCTIONS FOR INSTALLING INOX ESC LEVER TRIM FOR
ED
9
3CVR SERIES CONCEALED VERTICAL ROD EXIT DEVICE
INSTRUCTIONS FOR INSTALLING INOX WOOD DOOR ESC TRIM
ED
9
3CVR SERIES CONCEALED VERTICAL ROD EXIT DEVICE
