fnox
®
INSTRUCTIONS FOR INSTALLING ED93F-CVRW
u s
A
SERIES CONCEALED VERTICAL ROD EXIT DEVICE
1. PREPARE DOOR
And Prepare Top and Bottom Strike to Wood frame template
-------1-11/16"
TOP CASE
lP�i
, a
�""'
---5·7/32"'-�----·
-
,!,
INSIDE FACE
OF DOOR
(i?,BEVEL
3/8"
I •
=f
2-314"
BACKSET
&BOLl
..------1-25/32"
---------1
I :---------
I
NO SCALE
- INNER
CHASSIS
ASSEMBLY
r--
(0
�
l_ --
L-P=='==='==+='===!--,L--L
BOTTOM
PLATE
22
2-1/2"
4-1/8"
'
'
I
�-�-r; __
J
5/8"-+--.;-
i
+-
1
+-!
H
ii:
,-L,-L.
25132"
� OF
LATCHBOLT
&RODS
1
I
112"
2. MOUNT ROD & CHASSIS
Use Strike Furnished
. Attach inner chassis and its mounting plate to
door with 2 wood screw.
. Screw top and bottom rods into inner chassis,
and insert this ass'y into the door and fasten
inner chassis in place with 2 machine screws.
. Adj top and bottom rods to project bolt 1/2",
. Attach Main Chassis with 1 machine screws to
the inner chassis, and 2 machine screw to the
inner chassis mounting plate, and 4 wood
screws to the door.
. Attach Rail assembly to chassis with 2 truss
head machine screws. Attach the hinge stile
end of rail to the door with mounting plate,
718"
FULL RAD
,
INSIDE FACE
OF DOOR
� OF
LATCHBOLT
&RODS
(t, OF RAIL
-��ASSEMBLY
'-Ti-(
: I :
I
-,-
'
)
I
SEE
VIEW
"X"
1-11/32"
X
1/8"
DEEP
I
I
I
I
I
I
I
,-- -r-
(j:,
OF DEVICE
-&-RAIL
�
i
�r---:;r7t---j----jc'"-;r-7"'j-2-1/4"
r:r-�
41" FROM
FINISHED
FLOOR
i--
i
'--:;
1o DEEP
'I'
TI
l�
41"
FROM
FINISHED
FLOOR
Tl
j �
REQUIRED DOOR
UNDERCUT IS
114" FROM
FINISHED FLOOR
(PANIC & FIRE)
' '
! i !
' '
!
1'
!
'
'
-----.. ____ .... _____ ,
LHRB SHOWN
RHRB OPPOSITE
VIEWX"
f
(NO SCALE)
1-21/32"
3.2. Depress arm into rail opening and slide rail onto chassis.
3.3. With push rail depressed, adjust top bolt flush with top of the door,
and bottom bolt flush with bottom of the door.
3.4, Insert top chassis into cutout at the top of the door, and attach with
six wood screws.
VERTICAL
REFERENCE LINE
(CHASSIS)
RAIL MUST OVERLAP STILE BY 5/16" MIN
MOUNTING RAIL
X - CUT-OFF LENGTH
Y-----------l.i
MARK CUT-OFF POINT
ON MOUNTING RAIL
CUT-OFF AND DEBURR
INSER�
HINGE STILE
4. ATTACH COVER
---------- +---------fr-----------!E-
(4)3/16"•24 FL HD,
MACHNE
BOTTOM STRIKE
�rtjr!i-J]1=
zp
r-
2-518"
---J
1-{�
-�
3. MOUNT RAIL ASSEM
BLY
3.1. Determine cut-off dimension "X" by subtracting 1-1/8" from dimension "Y".
- Attach end cap to mounting plate with two cover screws
- Attach cover to chassis with four cover screws.
Attach cover to
chassis with four
cover screws
5. OPERATION CHECK
Attach end cap to
mounting plate with
four cover screws
5.1. Depress Push rail, bolt should retract into door.
The latch retractor button should pop out and hold the bolt retracted
until button is depressed.
5.2. If button does not pop out, remove top chassis and screw the top rod in
one turn. Replace top chassis and repeat abv operation.
E
D93
