KERN KERN AEJ Скачать руководство пользователя страница 3

1  Basic information  

Grundlegende Hinweise 

 
 

The device must be repaired only by trained specialist staff or personnel with 
professional formation (such as a repair-specialist accredited by law  
concerning verification).  

 

The service manual is obligatory for repair work. 

 

After repair, original conditions of the device have to be restored.  

 

Only original spare parts should be used. 
 
 
Instructions about conformity-evaluated scales: 

 

Repair must be carried only at 100% compliance with the type approval.  
A violation of this specification will result in a loss of the type approval! 

 

After successful repair the balance will have to be reverified before it can be 
used again in a statutorily regulated field. 
 
 

 
 
 
Das Gerät darf nur von geschultem oder beruflich ausgebildetem  
Fachpersonal (z. B. eichrechtlich anerkannter Instandsetzer) repariert werden.  

 

Die Serviceanleitung ist bindend für Reparaturen. 

 

Das Gerät muss nach erfolgter Reparatur wieder in den Originalzustand  
zurückversetzt werden.  

 

Es dürfen nur Originalersatzteile verwendet werden. 
 
 
Hinweis zu konformitätsbewerteten Waagen: 

 

Reparatur darf nur in 100% -iger Übereinstimmung mit der  
Bauartzulassung erfolgen. Ein Verstoß gegen diese Vorgabe führt zum Erlöschen 
der Bauartzulassung! 

 

Nach erfolgreicher Reparatur muss eine Nacheichung erfolgen, um die Waage  
wieder im gesetzlich geregelten Bereich verwenden zu können. 
 
 
 
 
 
 
 
 

3

Содержание KERN AEJ

































Отзывы: