Kenwood TK-5210 Скачать руководство пользователя страница 41

Страница: 41 / 66

■

Reviewing Messages in the Stack Memory

Press and hold the key programmed as

Selcall

Status

S Status

for second to enter Stack mode.

• The last received message is displayed with the message

number.

Press the

Side 2

and

Side 3

keys to select the desired

message.

Press the

Side 1

key to return to normal operation.

• To delete the selected message, press the

key. To

confirm the deletion, press the

key again.

• To delete all messages, press and hold the

key for

second. To confirm the deletion, press the

key

again.

hort

eSSAgeS

To send a short message, you must connect the transceiver to

a PC. Ask your dealer for details.

• Short messages can contain a maximum of 8 characters.
• On K2/K3/K/K/K7 model transceivers, received short messages

are displayed the same as Status messages and are stored in the

same stack memory. A combined maximum of Status calls and

short messages can be stored in the stack memory.

ong

eSSAgeS

To send and receive long messages, you must connect the

transceiver to a PC. Ask your dealer for details.

• Long messages can contain a maximum of 0 characters.

gpS r

eport

To send your location data, you must first connect a GPS

microphone to the transceiver. GPS data can be transmitted

using of methods: auto transmission, upon request, manual

transmission, upon pressing/releasing the

PTT

switch, and

during emergency mode. Ask your dealer for details.

Содержание TK-5210



































































Результаты поиска

Содержание TK-5210

Отзывы:

Kenwood TK-5210, Инструкция по эксплуатации, Страница: 41 / 66

Результаты поиска

Содержание TK-5210

Отзывы: