Kenwood MultiPro XL Weigh+ FDM72, Инструкция по эксплуатации

Страница: 11 / 231

6
27
Blend-Xtract 2GO
(if supplied)
a
Dispensing lid
b
Bottle
c
Sealing ring
d
Blade assembly
1 Add ingredients to the bottle up to the
400ml level mark.
O
For best blending performance always add
ice/frozen ingredients to the bottle first.
O
When adding frozen ingredients (i.e. frozen
fruit, yoghurt, ice cream or ice) do not blend
more than 60g or 3 ice cubes.
O
Do not blend frozen ingredients without
liquid.
2 Fit the sealing ring to the blade unit, ensuring
the seal is located correctly in the grooved
area.
O
Leaking will occur if the seal is damaged or
incorrectly fitted.
3 Hold the underside of the blade unit and
lower it onto the bottle, blades down.
4 Screw the blade holder onto the bottle - turn
clockwise to lock.
O
Shake to disperse the ingredients.
O
Place the blender onto the power unit and
turn clockwise to lock.
5 Select maximum speed. Allow the ingredients
to blend until smooth.
O
Once your drink has reached the desired
consistency, you can use the pulse (P) to
ensure all ingredients are thoroughly blended.
Hints and Tips
O
Note that when the bottle is filled to max
capacity (400ml), this is approximately two
servings.
O
If you do not intend to consume your drink
immediately, keep it refrigerated.
O
Ensure your drink is thin enough to be able
to drink from the dispensing lid. To make a
thinner drink add more liquid.
O
After blending, some drinks may not be
completely smooth due to seeds or the
fibrous nature of ingredients.
O
Some drinks may separate on standing,
therefore it is best to drink them straight
away. Separated drinks should be stirred
before drinking.
O
When the dispensing lid is fitted always keep
the bottle upright.
Using the drinking lid
1 Fit and lock the lid by turning clockwise.
2 When you want to drink, simply flip open the
lid cover. The drink can be consumed straight
from the bottle.
28
Juice Extractor
(if supplied)
a
Pusher
b
Juicer lid
c
Pulp remover
d
Filter drum
e
Bowl
f
Juicing spout
To use the juice extractor
1 Fit the juicer bowl to the power unit, turn
clockwise until it locks - the spout should
be situated to the left side when the bowl is
fitted correctly.
2 Place the pulp remover into the filter drum -
ensuring the tabs locate with the slots in the
bottom of the drum.
3 Fit the filter drum
4 Fit the attachment lid - turn clockwise until
it locks.
Your juicer will not operate if the
bowl or lid are not fitted correctly into the
interlock .
5 Place a suitable glass or jug under the juice
outlet.
6 Cut the food to fit the feed tube.
7 Switch on and push down evenly with the
pusher - never put your fingers in the feed
tube. Process fully before adding more.
O
After adding the last piece, let the juicer run
for a further 30 seconds to extract all the
juice from the filter drum.
Important
O
If the juicer starts to vibrate, switch off and
empty the pulp from the drum. The juicer
vibrates if the pulp becomes unevenly
distributed.
O
Some very hard foods may make your juicer
slow down or stop. If this happens switch off
and unblock the filter.
O
Switch off and clear the pulp collector
regularly during use.
Hints and Tips
O
Before processing remove stones and pips
(eg pepper, melon, plum) and tough skins
(e.g. melon, pineapple). You do not need to
peel or core apples and pears.
O
Use firm, fresh fruit and vegetables.
29
Express Dice
(if supplied)
a
Adjustable disc - dicing setting
b
Dicing grid
c
Dicing pusher
Important:
O
The dicing position on the adjustable
slicing disc is designed only to be used with
the dicing attachment.