KDC-W808/X689
13
●
How to enter the test mode
In order to enter the test mode, reset the unit while simulta-
neously pressing down [1] and [3] keys.
●
How to clear the test mode
Resetting only.
●
Initial conditions of the test mode
• Source is STANDBY.
• Displays lights are all turned on.
• The volume is at -10dB (The display is 30).
• Loudness (LOUD) is OFF.
• CRSC is OFF, regardless of whether there are switching
functions or not.
• SYSTEM Q is NATURAL (= FLAT).
• BEEP will sound anytime with a short push.
• Auxiliary (AUX) is ON.
• DISPLAY TYPE is TYPE C
• TUNER source display will be as follows
<E type>
Upper column = PS/Frequency,
Middle column = Spectrum analyzer,
Lower column = Indicator
<M / K type> Upper column = SNPS,
Middle column = Spectrum analyzer,
Lower column = Indicator
• CD source display will be as shown below.
<E / K type> Upper column = P-TIME,
Middle column = Spectrum analyzer,
Lower column = Blank
• SWPRE is SUB WOOFER ( 2 PREOUT models ).
●
RDS automatic measurement
Conventionally, the PS display has been visually checked on
the production line. This will be replaced by a new processing.
The PS data will be received and the PS contents is to be
verified as “RDS_TEST.”When this is verified, the P-CON ter-
minal is forced to go OFF. ( In this case, “_” means blank.)
→
This will be a dedicated test mode processing.
On the P-CON, when power is turned off once and, then,
turned on again, (Power OFF
→
ON ) the unit will be re-
started.
●
Special display when set to TUNER
When in TUNER mode, if any of the following displays appear,
there is an abnormality with the front end.
• “TNE2P_NG” : The E2PROM is still with the default (un-
specified) value, due to the fact that the front-end being
shipped without going through the adjustment process.
• “TNCON_NG” : In this condition, the communication with
TEST MODE
the front end is not possible.
●
Forced switching of K3I
In TUNER FM mode, each time [6] key is pressed, the func-
tions move in the following cycle : AUTO
→
forced WIDE
→
forced MIDDLE
→
force NARROW
→
AUTO. The initial con-
dition is AUTO and the displays below will appear.
• AUTO : FMA
• Forced WIDE : FMW
• Forced MIDDLE : FMM
• Forced NARROW : FMN
●
CD receiver test mode specifications
• Jumps are made to the following tracks by pressing the [
]
key.
No.9
→
No.15
→
No.10
→
No.11
→
No.12
→
No.13
→
No.22
→
No.14
→
No.9 (Returns to the beginning)
It must be noted, however, that when paying MP3/WMA/
AAC disk, which contain 8 files or less, the first track and the
following tracks are played in order.
• When [
] key is pressed, it goes down by one track.
• When a CD is used as a source, by short-pressing [1] key, a
jump to the Track No.28 is made.
• When a CD is used as a source, by short-pressing [2] key, a
jump to the Track No.14 is made.
• When a CD is used as a source, by short-pressing [3] key,
the model name and the version of CD mechanism will be
displayed in the upper column. When the [3] key is short
pressed again, normal display will resume. (Time Code dis-
play.)
• When a CD is used as a source, by short-pressing [6] key, a
jump to the Track No.15 is made. At the same time, the vol-
ume value is set to 25 (2V PRE) and 27 (5V PRE).
●
Audio Adjust mode
• By short-pressing [AUD] key, the Audio Adjust mode is en-
tered.
• As with the [AUD] key, [*] key on the remote controller can
be used to enter the Audio Adjust mode.
• As for the adjustment items, items for both the AUDIO FUNC-
TION MODE and SETUP MODE are included.
• The first item is the Fader which is followed by : Balance
→
Bass Level
→
Middle Level
→
Treble Level
→
( Sub Woofer
Level )
→
HPF Front
→
HPF Rear
→
LPF Sub Woofer. (Af-
ter this, any of the item can be selected)
* Normally, Sub Woofer Level is not included. In this version,
however, the Sub Woofer Level is included, and this has
been already arranged.
• With the remote controller, continuous forwarding is prohib-
ited.
• Using the VOL knob, the Fader is to be adjusted to the fol-
