Combined impedance
FCC WARNING
This e
q
uipment may generate or use radio fre
q
uency energy.
Changes or modifications to this e
q
uipment may cause harmful
interference unless the modifications are expressly approved in the
instruction manual. The user could lose the authority to operate
this e
q
uipment if an unauthori
z
ed change or modification is made.
FCC NOTE
This e
q
uipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This e
q
uipment may cause harmful
interference to radio communications, if it is not installed
and used in accordance with the instructions. However,
there is no guarantee that interference will not occur in a
particular installation. If this e
q
uipment does cause harmful
interference to radio or television reception, which can be
determined by turning the e
q
uipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the e
q
uipment and receiver.
• Connect the e
q
uipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
Safety precautions
WARNING
To prevent injury or fire, take the following
precautions:
• Mounting and wiring this product re
q
uires skills and
experience. For safety’s sake, leave the mounting and
wiring work to professionals.
• When extending the ignition, battery, or ground wires,
make sure to use automotive-grade wires or other wires
with the range of 5 mm²
(
AW
G
10
)
or more to prevent
wire deterioration and damage to the wire coating.
• To prevent a short circuit, never put or leave any metallic
objects
(
such as coins or metal tools
)
inside the unit.
• If the unit starts to emit smoke or strange smells, turn
off the power immediately and consult your Kenwood
dealer.
• Do not touch the unit during use because the surface of
the unit becomes hot and may cause burns if touched.
CAUTION
To prevent damage to the machine, take the following
precautions:
• Be sure the unit is connected to a 12V DC power supply
with a negative ground connection.
• Do not open the top or bottom covers of the unit.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid places
with too much dust or the possibility of water splashing.
• When replacing a fuse, only use a new one with the
prescribed rating. Using a fuse with the wrong rating
may cause your unit to malfunction.
• To prevent a short circuit when replacing a fuse, first
disconnect the wiring harness.
NOTE
• If you experience problems during installation, consult
your Kenwood dealer.
• If the unit does not seem to be working right, consult
your Kenwood dealer.
Cleaning the unit
If the front panel gets dirty, turn off the power and wipe
the panel with a dry silicon cloth or soft cloth.
CAUTION
Do not wipe the panel with a hard cloth or a cloth
dampened by volatile solvents such as paint thinner and
alcohol. They can scratch the surface of the panel and/or
cause the indicator letters to peel off.
To prevent battery rise
When the unit is used in the ACC O
N
position without
turning the engine O
N
, it depletes the battery. Use it after
starting the engine.
Protection function
The protection function is activated in the following situations:
This unit is e
q
uipped with a protection function for
protecting this unit and your speakers from various
accidents or problems that can occur.
When the protection function is triggered, the amplifier
stops operating.
Power indicator goes off:
• When the unit malfunctions
.
• When the internal temperature is high and unit won’t operate.
Power indicator lights continuously:
• When a speaker wire may be short-circuited.
• When a speaker output contacts ground.
7
Wiring
• Take the battery wire for this unit directly from the
battery. If it’s connected to the vehicle’s wiring harness, it
can cause blown fuses etc.
• If a bu
zz
ing noise is heard from the speakers when the
engine is running, connect a line noise filter
(
optional
)
to
each of the battery wire.
• Do not allow the wire to directly contact the edge of the
iron plate by using
G
rommets.
• Connect the ground wire to a metal part of the car
chassis that acts as an electrical ground passing
electricity to the battery‘s negative
·
terminal. Do not
turn the power on if the ground wire is not connected.
• Be sure to install a protective fuse in the power cord
near the battery. The protective fuse should be the same
capacity as the unit’s fuse capacity or somewhat larger.
• For the power cord and ground, use a vehicle type
(
fireproof
)
power wring cord.
(
Use a power wiring cord
with the range of 5 mm²
(
AW
G
10
)
or more.
)
• When more than one power amplifier are going to be
used, use a power supply wiring wire and protective
fuse of greater current-handling capacity than the total
maximum current drawn by each amplifier.
7
Speaker selection
• Using speakers with smaller input ratings than the
amplifier’s output power would result in smoke
generation or e
q
uipment failure.
• The impedance of the speakers that are going to
be connected should be 2Ω or greater
(
for stereo
connections
)
, or 4Ω or greater
(
for bridged connections
)
.
When more than one set of speakers are going to be
used, calculate the combined impedance of the speakers
and then connect suitable speakers to the amplifier.
<Example>
KAC-M3004̲K̲EnFrEs̲00.indd 1
15/01/15 10:33
