Installation Procedure :
Screw in the two 10x50 self taping screws (supplied with the package) on a same
horizontal level at a distance of 7.6 inches (192 mm) from each other in the
wall.
Carefully hang the purifier on the wall with the help of wall mounting slot
holes present on the back side of the purifier as shown in the figure below.
Fix the SS ball valve to the 1/4 inch port of the 3-way connector as shown in the
figure.
Connect the 3-way connector to the raw water supply as shown in the
figure. The threaded end of the 3-way connector is fitted in line with the raw
water supply. The other end can be connected to a tap or can be plugged
off if not required.
Now connect one end of the white pipe to the SS ball valve and other end to the
upper push fit elbow fitting on the left hand side of the purifier labeled as WATER IN.
Similarly, connect one end of the white pipe to the lower elbow fitting connector in
tank labeled as REJECT WATER and leave the other end in the drain.
nd
Fix the 2 SS ball valve to the
3/8
inch port at the bottom, left side of the water tank.
Remove dead plug before connection as shown in the figure.
Before connecting the power supply, it is important that you perform the following
functions:
Open the SS ball valve (Handle parallel to the ball valve) to start the flow of
water into the purifier.
Wait for 2-3 minutes to ensure that the filters are soaked in water.
Always keep the SS ball valve in close position present at the bottom of water
storage tank (Handle horizontal to the ball valve). Open it whenever you
require to use rejected water.
1.
2.
3.
4.
5.
6.
8.
(I)
(ii)
(iii)
7.
TM
The
Supreme
Mineral RO
Water Purifier is a product of advanced technology, which ensures safe
and clean drinking water. The purifier is easy and convenient to install.
Recommended Site Preparations :
single phase AC connection not more than 3 m away from the point of installation of
purifier
Raw water supply with ½ inch nipple not more than 3 m away
Drain for rejected water not more than 3m away
Space as per dimensions of the purifier
Wall/plane surface for mounting two screws and holding the machine
Specific Instructions :
TM
Supreme
Mineral RO is a wall mountable purifier. Make sure that it is only mounted on a wall.
Avoid installation on wooden and metallic stands
For optimum performance and minimum inlet pressure required, ensure that the raw water supply tank
is at least 10 ft above the level at which the purifier is installed
It is preferable to install the purifier near a sink so that inlet and reject water lines are easily available
The system and installation needs to comply with state and local laws &
regulations
KENT
KENT
n
n
n
n
n
n
n
n
n
100 - 250 V , 50-60Hz
Installation Instructions
6
UV Fail Alarm*
To ensure delivery of purer and healthier water, a micro-processor is installed in the purifier that performs
the following functions: -
UV Stabilization Delay: To ensure that the UV lamp is pre-heated and is working at its optimum
level before it starts disinfecting water, the controller provides a two seconds delay to UV lamp when the purifier
is switched on. During this period, only the UV lamp is switched on and other electrical devices of the purifier
are switched off.
Purification Delay: To ensure that the idle water lying in the internal pipes and in the UV chamber is disinfected
before being passed into the storage tank, the system provides 5 second delay when the purifier is switched on.
During this time, the UV lamp kills all micro-organisms that may be in the water inside UV chamber. After this
delay, all other electrical devices such as booster pump and solenoid valve are switched on to start normal
purification process.
Audible Alarm: The controller also controls the timing of UV Fail Alarm and the Filter Change Alarm.
Computer Controlled Operation*
n
n
n
n
n
The purifier automatically shuts off when the
The purifier automatically restarts when water
storage tanks are full
level drops below the maximum
The purifier automatically flushes & cleans the RO
The purifier does not allow any water rejection in
membrane on periodic intervals
absence of electricity or when tank is full
The purifier does not start if the inlet water supply
2
pressure is below 0.3 kg/cm
Automatic Operation
KENT
TM
Supreme
Mineral RO has an in-built feature that sounds an audible alarm if the UV lamp malfunctions. This
feature is provided to ensure purity. This UV Fail Alarm will sound as follows:
Two short beeps after every two seconds.
In case such an alarm is audible, kindly switch off the purifier and call the service technician for help.
The purifier will stop its purification process in such a circumstance.
2 Sec.
2 Sec.
2 Sec.
2 Sec.
5
Filter Change Alarm*
KENT
TM
Supreme
Mineral RO has an in-built feature that sounds an audible alarm to indicate replacement
time for filters. This alarm will be audible after
The Filter Change Alarm will sound as follows:
4 short beeps after every two seconds; for 30 seconds. The alarm will repeat after every 2 hours of use.
In case such an alarm is audible, please call the service technician and request him to change the filters of the
purifier. However, if the filters are not changed within the next 60 hours of operation, the purifier will stop
functioning to ensure purity and hygiene. The following alarm will be audible after 60 Hrs. A continuous beep
for an infinite time.
In case, such an alarm is audible, kindly switch off the purifier and call the service technician to replace
the filters. In such a circumstance, the purifier will not function unless the filters are changed.
700 hrs of use since the last filter change (or since the time of
installation).
2 Hours
30 Sec.
30 Sec.
* Tested & Certified by TUV-SUD South Asia (P) Ltd.
Slot holes
