9
10
* Tested & Certified by TUV-SUD South Asia (P) Ltd.
** Tested or certified flushing time - 24hrs.
To ensure that the purifier operates at its best, a routine maintenance must be performed. The frequency
of the maintenance will greatly depend upon the raw water quality and consumption of purified water.
• Storage tank must be cleaned once in a
week (Refer Cleaning the Water Tank)
• Replace sediment filter and activated carbon
filter once in 12 months or earlier if they get
clogged. It is recommended to change the
FRT along with the filters
• Replace RO membrane once in a year or
earlier if it gets clogged
• Replace UF membrane once in a year or
earlier if it gets clogged
• Replace the UV Lamp once in a year
• In the event of not using purifier for a long
time (while going for a holiday, tour, etc.),
ensure that you disconnect the power
supply, turn off the raw water supply and
drain out the storage tank
Maintenance
TDS Adjustment*
The unique TDS Controller enables customers to retain the contents of natural minerals in purified water,
as per their requirement.
• Turning the screw of the valve anti-clockwise
results in an increased mineral content
• Turning the screw of the valve clockwise
results in a decreased mineral content
We recommend keeping the TDS at the lowest possible level but not below 50mg/l.
• Switch on the power supply
• Allow the storage tank to fill till the
maximum level**
• Switch off the power supply
• Open the upper cover, lift and drain the
storage tank to remove residual dust
particles present inside the pipe and
storage tank
• Place back the storage tank and close the
upper cover
• Switch on the power supply
• Purifier is ready to use
Starting-up the Purifier
The glowing Red LED indicates that the power is ON. The glowing Green LED indicates that
the purification process is ON.
1. another end to the upper push-fit elbow fitting to the left hand side
of the purifier labelled as WATER IN, as shown in fig 1.
2. Similarly, connect one end of the white pipe to the lower elbow
fitting connector in tank labelled as REJECT WATER and leave the
other end in the overhead tank, as shown in fig 2.
Step-3
1. Connect the power supply.
2. Installation is complete.
Before connecting the power supply, it is important that you perform
the following functions:
1. Open the SS ball valve (Handle parallel to the ball valve) to start the
flow of water into the purifier, as shown in the figure.
2. Wait for 2-3 minutes to ensure that the filters are soaked in water.
Step-4
Step-5
The Reverse Osmosis System contains a replaceable treatment component critical for the effective
reduction of total dissolved solids and that product water shall be tested periodically to verify that the
system is performing properly.
-20010
SP Inline Sediment Filter 8"
-20529
SP RO Membrane
-20009
SP Inline Carbon Filter 8"
-20015
SP Post Carbon Filter (Blue)
-20003
SP Hollow Fibre Membrane (RO)
-20020
SP FRT 300/450
Note:
Filters and membrane are consumables. Their replacement time depends upon the quality of raw
water and water consumption. They are not covered under the warranty. However, if a filter chokes
within six months and a membrane within a year, it will be cleaned/repaired/replaced free of cost.
Changing the filters and system inspection is available on call. The purification capacity of RO
membranes will reduce with time due to clogging of pores of membranes.
Replacement of spare parts are as under:-
• If the supply cord is damaged, it must be replaced by the original part in order to avoid hazard.
• Children should be supervised to ensure that they do not play with the appliance
• This appliance is not intended for use by persons (including children) with reduced physical,sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety
• Do not operate the UV-C emitter when it is removed from the appliance enclosure.
• Read the maintenance instructions before opening the appliance.
• The appliance must be disconnected from the supply before replacing the UV-C emitter.
Important Safety Instructions
Warning
