If UV Lamp fails, machine will display a blinking warning
signal of UV failure and an alarm with a single beep. will be
audible The purifier would stop purifying water till the UV
lamp is replaced.
If UV LED fails, machine will display a blinking warning
signal of UV failure and an alarm with two beeps will be
audible.
If the interface shows a UV failure message, switch off the
purifier and call a service technician for help.
On exhaustion of filter life, 'Replacement Filter message'
will be displayed on screen with a continuous buzzer
and the purifier will stop purifying water till filters are not
replaced.
If the interface shows 'Replace Filter Message', switch
off the purifier and call a service technician for help.
Low RO flow warning sign indicates reduced capacity of
RO Membrane.
All though the water purifier will continue working till the
membrane failure happens, it is recommended to call
the KENT Customer Care and ask for Membrane
Replacement.
UV Lamp Failure/LED Failure
Filter Replacement
Low RO Flow
To ensure delivery of purer and healthier water, a micro-processor is installed in the purifier that performs
the following functions:-
UV Stabilization Delay:
To ensure that the UV lamp is pre-heated and is working at its optimum level
before it starts disinfecting water, the controller provides a two second delay to the UV lamp when the
purifier is switched on. During this period, only the UV lamp is switched on and other electrical devices
of the purifier are switched off.
Purification Delay:
To ensure that the idle water lying in the internal pipes and in the UV chamber is
disinfected before being passed into the storage tank, the system provides a 5 second delay when the
purifier is switched on. During this time, the UV lamp kills all micro-organisms that may be in the water
inside the UV chamber. After this delay, all other electrical devices such as the booster pump and
solenoid valve are switched on to start normal purification process.
Alarm: To ensure delivery of purer water, KENT ACE Star in-built micro controller controls and senses
various vital components and displays their status on the digital interface.
Computer Controlled Operation
• The purifier automatically shuts off when the
storage tank is full
• The purifier does not start if the inlet water
supply pressure falls below 0.3 kg/cm²
• The purifier automatically restarts when the
water level drops below the maximum
• The purifier does not allow any water rejection
in absence of electricity/when tank is full
Automatic Operation
The KENT ACE Star Mineral RO™ Water Purifier is a product of advanced technology, which ensures
safe and clean drinking water. The purifier is easy and convenient to install.
Recommended Site Preparations:
• Single Phase 100-250 V AC, 50-60 Hz.
connection not more than 3m away from the
point of installation of the purifier
• Raw water supply with ½ inch nipple not more
than 3m away
• Drain for rejected water not more than 3m away
• Space as perthe dimensions of the purifier
• Wall/plane surface for mounting two screws
and holding the machine
• The system and installation must comply with
state and local laws & regulations
Specific Instructions:
• KENT ACE Star Mineral RO™ Water Purifier is
a wall mountable purifier. Make sure that it is
only mounted on a wall. Avoid installation on
wooden and metallic stands
• For optimum performance and minimum inlet
pressure required, ensure that the raw water
supply tank is at least 10 ft. above the
purifier
• It is preferable to install the purifier near a sink
so that the inlet and reject water lines are easily
available
Installation Instructions
7
8
Step-2
Figure 1.
Figure 2.
Figure 4.
Figure 3.
1
2
3
4
4
2
1
3
1. First fix the SS ball valve (marked as no. 4) to the 1/4 inch port of the 3-way connecter (marked as no. 2)
as shown in figure 2.
2. Connect the 3-way connector to the raw water supply (marked as no. 1) as shown in the figure 3. The
3-way connector is fit in line with the raw water supply.
3. The other end of the 3-way connector can be connected to a tap (marked as no.3) as shown in figure
or can be plugged off if not required.
1. Paste the central drill sticker on a wall at 3.6 Feet to 4.0 Feet from the ground as per your convenience.
2. Ensure that the sticker is pasted straight on the wall, then drill holes as per the space provided on the sticker.
3. Now, insert the puff up with the help of a hammer
4. Screw in two 10X50 self-taping screws, 5.4 inches (138 mm) apart horizontally
5. Carefully hang the purifier on the wall with the help of wall-mounting slot holes provided on back side of the purifier
Note:
1. If the wall is not straight or the screws are not properly drilled in an even position, it will damage your purifier.
2. Keep the device away from heat or direct sunlight
Installation Procedure:
Step-1
RO
FLOW
FILTER
LIFE
POWER
CHANGE FILTERS
FOR SERVICE, CALL
92789-12345
MINERALS
GOOD
LO
W
HIG
H
