INSTRUCTION MANUAL FOR USE AND MAINTENANCE
8
08812946(3)2003-08
USE
By means of this Manual, the operator must learn the
meaning of these symbols.
Do not cover these plates for any reason, in case of da-
mage replace them immediately.
BATTERY CHECK/SETTING ON A NEW
MACHINE
– The electric components of this machine can be
seriously damaged if batteries are either installed or
connected improperly. Batteries can be installed by
qualified personnel only. Set the machine electronic
board and the integrated battery charger according
to the type of batteries used (lead or gel batteries).
– Check the batteries for damage before installation.
– Disconnect the battery connector or the battery
charger plug.
– Move the batteries with great care.
– Be sure that the battery charger cables are properly
connected to the battery terminals according to their
polarity.
– Install the battery terminal protection caps supplied
with the machine.
The machine needs two 12 V batteries, connected ac-
cording to the diagram (15, Fig. H).
The machine can be set in one of the following modes:
a)
With (lead or gel) batteries installed on the
machine and ready to be used.
b)
With lead batteries installed on the machine but
without liquid electrolyte.
c)
Without battery
According to these conditions, operate as described
below.
a)
(Lead or gel) batteries supplied and already
installed on the machine and ready to be used.
1.
Check that the batteries are connected to the
machine by means of the connector (25, Fig. C).
2.
Start the machine by means of the brush and
suction push-buttons (5 and 6, Fig. B). If the green
warning light (2, Fig. B) turns on, the batteries are
ready to be used. If the warning lights (3 or 4, Fig.
WARNING!
On some points of the machine there are
some decals indicating:
- DANGER
- WARNING
- CAUTION
- CONSULTATION
WARNING!
B) turn on, it is necessary to charge the batteries
(see procedure in chapter "Maintenance")
b)
Lead batteries supplied and already installed
on the machine but without liquid electrolyte.
1.
Remove the key (24, Fig. C) from its housing and
remove the tank assembly fastening screw (1, Fig.
H).
2.
Carefully lift the tank assembly (19, Fig. H) by
means of the manoeuver handle (2, Fig. C).
3.
Remove the battery caps (14, Fig. H).
4.
Fill up each battery element with sulfuric acid for
batteries (density from 1.27 to 1.29 Kg at 25°C) in
accordance with the instructions specified in the
Battery Use and Maintenance Manual.
The correct quantity of sulfuric acid is indicated in
the Battery Use and Maintenance Manual.
5.
To avoid damaging the floor, dry with a cloth both
acid and water on the top of the batteries after
charge.
6.
Let the batteries rest for a few minutes and fill in
with sulfuric acid in accordance with the instruc-
tions specified in the Battery Use and Mainte-
nance Manual.
7.
Proceed with recharging the batteries (see the
procedure in the Maintenance paragraph).
c)
Without batteries
1.
Buy appropriate batteries (See paragraph
"Technical Characteristics" and the diagram 15,
Fig. H).
Apply to battery qualified retailers to choose and
install the battery.
2.
Install and set the machine batteries (WET or
GEL) and the battery charged according to the
type of battery, as described in the following
paragraph.
BATTERY INSTALLATION AND BATTERY
TYPE SETTING (WET OR GEL)
According to the chosen battery type (lead or gel) per-
form the setting of the electronic board of the machine
and the battery charger, operating as indicated below:
WARNING!
Please pay a strict attention when working
with sulfuric acid, as it is corrosive. If it
comes in contact with the skin or the eyes,
wash abundantly with water and call a
doctor.
Batteries have to be filled up in a properly
ventilated area.
Use protective gloves.
https://harrissupplyind.com - To Order Parts Call 608-268-8080
