Kenmore 625.3485400 Скачать руководство пользователя страница 7

Страница: 7 / 32

WATER SOFTENER START-UP

SECTION 1

1C.

PROGRAM THE TIMER

SET WATER HARDNESS NUMBER:

Press the #1 SELECT button once to

display 15 (flashing) and HARDNESS.

The grains per gallon (gpg)

hardness of your water sup-

ply is on your water analysis

report. Be sure to enter water

test results on page 2, for

future reference.

NOTE:

If your water supply contains iron, compensate

for it by adding to the water hardness number.

For example, assume your water is 15 gpg hard and

contains 2 ppm iron. Add 5 to the hardness number for

each 1 ppm of iron. In this example, you would use 25

for your hardness number.

15 gpg hardness

2 ppm iron x 5 = 10 +10

(times)

25 HARDNESS NUMBER

Press the UP/DOWN

buttons to set your

water hardness number in the display. The

DOWN button moves the display to 1. The UP

button moves the display to the highest setting

(see maximum setting for your model in the

specifications).

NOTE:

Each press of the UP/DOWN button changes the

display by 1 between 1 and 25. Between 25 and

the highest number, the display changes 5 at a

time

25, 30, 35, etc. Holding the UP or DOWN

button in changes the display twice each second.

SET RECHARGE (REGENERATION) TIME:

Press the #1 SELECT button to display 2:00

AM (flashing) and RECHARGE TIME.

At the 2:00 AM RECHARGE

TIME setting, the softener be-

gins regeneration (see pages

12 and 13) at 2:00 AM, ending

no later than 4:00 AM. This is a

good time in most households

because water is not being

used (see AUTOMATIC BY-

PASS, page 14). If a different

RECHARGE TIME setting

would be better for your

household, do the following.

Press the

UP/DOWN

buttons to set the

desired RECHARGE starting hour. Be sure to

observe the AM-PM as you did when setting the

present time of day.

NOTE:

Each press of the UP/DOWN buttons changes

the display 1 hour. Holding the buttons in

changes the display twice each second.

Press the #1 SELECT button once again,

return the present time, and RECHARGE TO-

NIGHT in the display.

IF YOU NEED HELP PROGRAMMING THE TIMER, CALL TOLL FREE, NUMBER

1-800-426-9345.

SEE PAGES 10 AND 11 FOR OTHER FACE PLATE TIMER FEATURES.

Содержание 625.3485400

































Результаты поиска

Содержание 625.3485400

Отзывы:

Похожие инструкции для 625.3485400

Бренды по названию

Популярные бренды

Kenmore 625.3485400, Руководство пользователя

Результаты поиска

Содержание 625.3485400

Отзывы:

Похожие инструкции для 625.3485400

Бренды по названию

Популярные бренды